Terastation TS-8VHL
Specs
| CPU | Intel Atom D510 1.66GHz Dual-Core (64-bit) |
| Memory | 2 GB DDR2 (Upgradable to 4GB) |
| Bays | 8 |
| Network | 2x 10/100/1000 Mbps (Marvell 88e8059) |
| Sata | 8x SATA II (Intel 82801ir and Marvell 88SX7042) |
| USB 2.0 | 2x Back |
| USB 3.0 | No |
| Serial port | 1x Back |
| VGA | Yes |
| Fan | 2x |
| Power | Internal AC 100-240V, universal 50/60Hz |
Stock Firmware Installation
You can re-install the linux-based firmware by creating a recovery disk, see Create Recovery Disk for Intel-based Terastation You can then boot from it by switching the boot mode switch on the back to "USB", after a few minutes the device will go into EM Mode Then you can install the firmware using the firmware updater in debug mode, see Enable Debug mode for LSUpdater/TSUpdater
Custom Firmware/Operating System installation
These devices run on an Intel Atom processor with a fairly typical BIOS and include a VGA out and support USB keyboards, you should be able to run virtually any operating system that will run on a normal PC depending on drivers/etc.
For tools to help install and configure Debian on these devices, see Installing Debian on Intel Terastations
Pictures
DMESG output
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.31.8-atom_d510 (root@HP7907) (gcc version 4.2.0 20070413 (prerelease)) #2 SMP Wed Dec 22 12:29:42 JST 2021 [ 0.000000] Command line: root=sde1 rw usbboot=yes mode=initilize ts4000=no acc=no [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000400 - 000000000009e800 (usable) [ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bf580000 (usable) [ 0.000000] BIOS-e820: 00000000bf580000 - 00000000bf58e000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf5d0000 - 00000000bf5e0000 (reserved) [ 0.000000] BIOS-e820: 00000000bf5e7000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] e820 update range: 0000000000100000 - 0000000000100030 (usable) ==> (usable) [ 0.000000] extended physical RAM map: [ 0.000000] reserve setup_data: 0000000000000400 - 000000000009e800 (usable) [ 0.000000] reserve setup_data: 000000000009e800 - 00000000000a0000 (reserved) [ 0.000000] reserve setup_data: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] reserve setup_data: 0000000000100000 - 0000000000100030 (usable) [ 0.000000] reserve setup_data: 0000000000100030 - 00000000bf580000 (usable) [ 0.000000] reserve setup_data: 00000000bf580000 - 00000000bf58e000 (ACPI data) [ 0.000000] reserve setup_data: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS) [ 0.000000] reserve setup_data: 00000000bf5d0000 - 00000000bf5e0000 (reserved) [ 0.000000] reserve setup_data: 00000000bf5e7000 - 00000000c0000000 (reserved) [ 0.000000] reserve setup_data: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] reserve setup_data: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] reserve setup_data: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] DMI present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-D7FFF write-protect [ 0.000000] D8000-DFFFF uncachable [ 0.000000] E0000-EFFFF write-through [ 0.000000] F0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask F00000000 write-back [ 0.000000] 1 base 100000000 mask FC0000000 write-back [ 0.000000] 2 base 0C0000000 mask FC0000000 uncachable [ 0.000000] 3 base 0BF600000 mask FFFF00000 write-through [ 0.000000] 4 base 0BF700000 mask FFFF00000 uncachable [ 0.000000] 5 base 0BF800000 mask FFF800000 uncachable [ 0.000000] 6 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x407050600070106, new 0x7010600070106 [ 0.000000] last_pfn = 0xbf580 max_arch_pfn = 0x400000000 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000400 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable) [ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 0000000000100030 (usable) [ 0.000000] modified: 0000000000100030 - 00000000bf580000 (usable) [ 0.000000] modified: 00000000bf580000 - 00000000bf58e000 (ACPI data) [ 0.000000] modified: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS) [ 0.000000] modified: 00000000bf5d0000 - 00000000bf5e0000 (reserved) [ 0.000000] modified: 00000000bf5e7000 - 00000000c0000000 (reserved) [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] modified: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] initial memory mapped : 0 - 20000000 [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf580000 [ 0.000000] 0000000000 - 00bf400000 page 2M [ 0.000000] 00bf400000 - 00bf580000 page 4k [ 0.000000] kernel direct mapping tables up to bf580000 @ 10000-15000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000140000000 [ 0.000000] 0100000000 - 0140000000 page 2M [ 0.000000] kernel direct mapping tables up to 140000000 @ 13000-19000 [ 0.000000] RAMDISK: 7eebf000 - 7fff6855 [ 0.000000] ACPI: RSDP 00000000000f9f30 00024 (v02 ACPIAM) [ 0.000000] ACPI: XSDT 00000000bf580100 00054 (v01 MATSU SLIC1108 20101228 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000bf580290 000F4 (v04 122810 FACP0918 20101228 MSFT 00000097) [ 0.000000] ACPI: DSDT 00000000bf5805c0 05CE6 (v02 WSQVL WSQVL301 00000301 INTL 20051117) [ 0.000000] ACPI: FACS 00000000bf58e000 00040 [ 0.000000] ACPI: APIC 00000000bf580390 0006C (v02 122810 APIC0918 20101228 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000bf580400 0003C (v01 122810 OEMMCFG 20101228 MSFT 00000097) [ 0.000000] ACPI: SLIC 00000000bf580440 00176 (v01 MATSU SLIC1108 20101228 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000bf58e040 00082 (v01 122810 OEMB0918 20101228 MSFT 00000097) [ 0.000000] ACPI: GSCI 00000000bf58e0d0 02024 (v01 122810 GMCHSCI 20101228 MSFT 00000097) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000140000000 [ 0.000000] Bootmem setup node 0 0000000000000000-0000000140000000 [ 0.000000] NODE_DATA [0000000000014000 - 0000000000018fff] [ 0.000000] bootmap [0000000000019000 - 0000000000040fff] pages 28 [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 0140000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] [ 0.000000] #2 [0001000000 - 0001933734] TEXT DATA BSS ==> [0001000000 - 0001933734] [ 0.000000] #3 [007eebf000 - 007fff6855] RAMDISK ==> [007eebf000 - 007fff6855] [ 0.000000] #4 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000] [ 0.000000] #5 [0000100000 - 0000100030] setup data 9 ==> [0000100000 - 0000100030] [ 0.000000] #6 [0001934000 - 000193420f] BRK ==> [0001934000 - 000193420f] [ 0.000000] #7 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000] [ 0.000000] #8 [0000013000 - 0000014000] PGTABLE ==> [0000013000 - 0000014000] [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 [ 0.000000] [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880028600000-ffff88002bdfffff] on node 0 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00140000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009e [ 0.000000] 0: 0x00000101 -> 0x000bf580 [ 0.000000] 0: 0x00100000 -> 0x00140000 [ 0.000000] On node 0 totalpages: 1045773 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 104 pages reserved [ 0.000000] DMA zone: 3821 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 14280 pages used for memmap [ 0.000000] DMA32 zone: 765368 pages, LIFO batch:31 [ 0.000000] Normal zone: 3584 pages used for memmap [ 0.000000] Normal zone: 258560 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000 [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 0000000000100000 - 0000000000101000 [ 0.000000] PM: Registered nosave memory: 00000000bf580000 - 00000000bf58e000 [ 0.000000] PM: Registered nosave memory: 00000000bf58e000 - 00000000bf5d0000 [ 0.000000] PM: Registered nosave memory: 00000000bf5d0000 - 00000000bf5e0000 [ 0.000000] PM: Registered nosave memory: 00000000bf5e0000 - 00000000bf5e7000 [ 0.000000] PM: Registered nosave memory: 00000000bf5e7000 - 00000000c0000000 [ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000 [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000 [ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ee00000) [ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 28 pages at ffff880028022000, static data 82848 bytes [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1027749 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=sde1 rw usbboot=yes mode=initilize ts4000=no acc=no [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.000000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000 [ 0.000000] software IO TLB at phys 0x20000000 - 0x24000000 [ 0.000000] Memory: 4032052k/5242880k available (5097k kernel code, 1059788k absent, 151040k reserved, 2891k data, 548k init) [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:440 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 1662.838 MHz processor. [ 0.000999] Console: colour EGA 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.67 BogoMIPS (lpj=1662838) [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Initializing. [ 0.000999] SELinux: Starting in permissive mode [ 0.001477] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.005168] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.006803] Mount-cache hash table entries: 256 [ 0.007305] Initializing cgroup subsys ns [ 0.007425] Initializing cgroup subsys cpuacct [ 0.007539] Initializing cgroup subsys freezer [ 0.007680] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.007810] CPU: L2 cache: 512K [ 0.007916] CPU 0/0x0 -> Node 0 [ 0.008012] CPU: Physical Processor ID: 0 [ 0.008120] CPU: Processor Core ID: 0 [ 0.008228] mce: CPU supports 5 MCE banks [ 0.008343] CPU0: Thermal LVT vector (0xfa) already installed [ 0.008350] using mwait in idle threads. [ 0.008457] Performance Counters: Atom events, Intel PMU driver. [ 0.008613] ... version: 3 [ 0.008719] ... bit width: 40 [ 0.008827] ... generic counters: 2 [ 0.008934] ... value mask: 000000ffffffffff [ 0.009005] ... max period: 000000007fffffff [ 0.009116] ... fixed-purpose counters: 3 [ 0.009223] ... counter mask: 0000000700000003 [ 0.009367] ACPI: Core revision 20090521 [ 0.023669] Setting APIC routing to flat [ 0.025233] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.035359] CPU0: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.035994] Booting processor 1 APIC 0x2 ip 0x6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 3324.55 BogoMIPS (lpj=1662276) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 1/0x2 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU1: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 1, old 0x407050600070106, new 0x7010600070106 [ 0.107947] CPU1: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.108120] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.109161] Booting processor 2 APIC 0x1 ip 0x6000 [ 0.000999] Initializing CPU#2 [ 0.000999] Calibrating delay using timer specific routine.. 3324.52 BogoMIPS (lpj=1662262) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 2/0x1 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 0 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU2: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 2, old 0x407050600070106, new 0x7010600070106 [ 0.182303] CPU2: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.184077] checking TSC synchronization [CPU#0 -> CPU#2]: passed. [ 0.185189] Booting processor 3 APIC 0x3 ip 0x6000 [ 0.000999] Initializing CPU#3 [ 0.000999] Calibrating delay using timer specific routine.. 3324.56 BogoMIPS (lpj=1662280) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 3/0x3 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU3: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 3, old 0x407050600070106, new 0x7010600070106 [ 0.258569] CPU3: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.259095] checking TSC synchronization [CPU#0 -> CPU#3]: passed. [ 0.259987] Brought up 4 CPUs [ 0.260096] Total of 4 processors activated (13299.31 BogoMIPS). [ 0.260354] khelper used greatest stack depth: 5864 bytes left [ 0.262077] xor: automatically using best checksumming function: generic_sse [ 0.266966] generic_sse: 5056.000 MB/sec [ 0.267076] xor: using function: generic_sse (5056.000 MB/sec) [ 0.267214] Time: 18:33:21 Date: 11/06/23 [ 0.267436] NET: Registered protocol family 16 [ 0.268990] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.269193] ACPI: bus type pci registered [ 0.269336] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.269336] PCI: Not using MMCONFIG. [ 0.269336] PCI: Using configuration type 1 for base access [ 0.283031] bio: create slab <bio-0> at 0 [ 0.286173] ACPI: EC: Look up EC in DSDT [ 0.309422] ACPI: Interpreter enabled [ 0.309542] ACPI: (supports S0 S1 S3 S4 S5) [ 0.309799] ACPI: Using IOAPIC for interrupt routing [ 0.310046] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.322670] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources [ 0.343211] PCI: Using MMCONFIG at e0000000 - efffffff [ 0.370182] ACPI Warning: Incorrect checksum in table [OEMB] - 4D, should be 4A 20090521 tbutils-246 [ 0.371432] ACPI Warning: Incorrect checksum in table [GSCI] - 6A, should be 3E 20090521 tbutils-246 [ 0.371960] ACPI: No dock devices found. [ 0.373365] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.373597] pci 0000:00:02.0: reg 10 32bit mmio: [0xfe680000-0xfe6fffff] [ 0.373597] pci 0000:00:02.0: reg 14 io port: [0xa880-0xa887] [ 0.373597] pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff] [ 0.373597] pci 0000:00:02.0: reg 1c 32bit mmio: [0xfe700000-0xfe7fffff] [ 0.373597] pci 0000:00:02.1: reg 10 32bit mmio: [0xfea00000-0xfea7ffff] [ 0.373597] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.374010] pci 0000:00:1c.0: PME# disabled [ 0.374188] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.374320] pci 0000:00:1c.4: PME# disabled [ 0.374499] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold [ 0.374616] pci 0000:00:1c.5: PME# disabled [ 0.374781] pci 0000:00:1d.0: reg 20 io port: [0xac00-0xac1f] [ 0.374860] pci 0000:00:1d.1: reg 20 io port: [0xb000-0xb01f] [ 0.375018] pci 0000:00:1d.2: reg 20 io port: [0xb080-0xb09f] [ 0.375103] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfeafb400-0xfeafb7ff] [ 0.375164] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.375281] pci 0000:00:1d.7: PME# disabled [ 0.375547] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.375562] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.375758] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.375878] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) [ 0.376079] pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407] [ 0.376089] pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03] [ 0.376099] pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887] [ 0.376109] pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803] [ 0.376119] pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f] [ 0.376130] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfeafb800-0xfeafbfff] [ 0.376167] pci 0000:00:1f.2: PME# supported from D3hot [ 0.376284] pci 0000:00:1f.2: PME# disabled [ 0.376467] pci 0000:04:00.0: reg 10 64bit mmio: [0xfeb00000-0xfebfffff] [ 0.376479] pci 0000:04:00.0: reg 18 io port: [0xe800-0xe8ff] [ 0.376587] pci 0000:00:1c.0: bridge io port: [0xe000-0xefff] [ 0.376596] pci 0000:00:1c.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff] [ 0.376606] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xc0000000-0xc01fffff] [ 0.377079] pci 0000:03:00.0: reg 10 64bit mmio: [0xfe9dc000-0xfe9dffff] [ 0.377152] pci 0000:03:00.0: reg 18 io port: [0xd800-0xd8ff] [ 0.377373] pci 0000:03:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9fffff] [ 0.377663] pci 0000:03:00.0: supports D1 D2 [ 0.377669] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.377819] pci 0000:03:00.0: PME# disabled [ 0.378117] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff] [ 0.378125] pci 0000:00:1c.4: bridge 32bit mmio: [0xfe900000-0xfe9fffff] [ 0.378136] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xc0200000-0xc03fffff] [ 0.378550] pci 0000:02:00.0: reg 10 64bit mmio: [0xfe8dc000-0xfe8dffff] [ 0.378626] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff] [ 0.378847] pci 0000:02:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff] [ 0.379150] pci 0000:02:00.0: supports D1 D2 [ 0.379156] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.379308] pci 0000:02:00.0: PME# disabled [ 0.379595] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff] [ 0.379603] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe800000-0xfe8fffff] [ 0.379613] pci 0000:00:1c.5: bridge 64bit mmio pref: [0xc0400000-0xc05fffff] [ 0.379675] pci 0000:00:1e.0: transparent bridge [ 0.379821] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.380167] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.380575] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.380741] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] [ 0.380881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] [ 0.411222] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15), disabled. [ 0.411893] ACPI: PCI Interrupt Link [LNKB] (IRQs *7), disabled. [ 0.412421] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15), disabled. [ 0.413124] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12 14 15), disabled. [ 0.413785] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.414480] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.415175] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.415852] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15), disabled. [ 0.417056] SCSI subsystem initialized [ 0.417294] libata version 3.00 loaded. [ 0.435190] raid6: int64x1 324 MB/s [ 0.452017] raid6: int64x2 500 MB/s [ 0.469020] raid6: int64x4 625 MB/s [ 0.486058] raid6: int64x8 667 MB/s [ 0.503076] raid6: sse2x1 613 MB/s [ 0.520012] raid6: sse2x2 1117 MB/s [ 0.537030] raid6: sse2x4 1972 MB/s [ 0.537138] raid6: using algorithm sse2x4 (1972 MB/s) [ 0.537325] PCI: Using ACPI for IRQ routing [ 0.556079] cfg80211: Using static regulatory domain info [ 0.556130] cfg80211: Regulatory domain: US [ 0.556240] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.556433] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.556551] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.556668] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.556786] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.557007] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.557125] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.557255] cfg80211: Calling CRDA for country: US [ 0.557394] NetLabel: Initializing [ 0.557394] NetLabel: domain hash size = 128 [ 0.557394] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.557394] NetLabel: unlabeled traffic allowed by default [ 0.558231] hpet clockevent registered [ 0.558240] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 0.558363] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.558569] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 0.571024] pnp: PnP ACPI init [ 0.571171] ACPI: bus type pnp registered [ 0.583423] pnp: PnP ACPI: found 14 devices [ 0.583541] ACPI: ACPI bus type pnp unregistered [ 0.583677] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved [ 0.583798] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved [ 0.583932] system 00:08: ioport range 0xa00-0xa0f has been reserved [ 0.584062] system 00:08: ioport range 0xa10-0xa1f has been reserved [ 0.584180] system 00:08: ioport range 0xa20-0xa2f has been reserved [ 0.584300] system 00:08: ioport range 0xa30-0xa3f has been reserved [ 0.584430] system 00:09: ioport range 0x4d0-0x4d1 has been reserved [ 0.584548] system 00:09: ioport range 0x800-0x87f has been reserved [ 0.584666] system 00:09: ioport range 0x480-0x4ff could not be reserved [ 0.584786] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.584907] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.585037] system 00:09: iomem range 0xfed40000-0xfed8ffff has been reserved [ 0.585168] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved [ 0.585366] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.585495] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved [ 0.585624] system 00:0d: iomem range 0x0-0x9ffff could not be reserved [ 0.585742] system 00:0d: iomem range 0xc0000-0xcffff has been reserved [ 0.585860] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved [ 0.585980] system 00:0d: iomem range 0x100000-0xbf6fffff could not be reserved [ 0.586185] system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved [ 0.592509] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 [ 0.592631] pci 0000:00:1c.0: IO window: 0xe000-0xefff [ 0.592746] pci 0000:00:1c.0: MEM window: 0xfeb00000-0xfebfffff [ 0.592864] pci 0000:00:1c.0: PREFETCH window: 0x000000c0000000-0x000000c01fffff [ 0.593071] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 [ 0.593187] pci 0000:00:1c.4: IO window: 0xd000-0xdfff [ 0.593304] pci 0000:00:1c.4: MEM window: 0xfe900000-0xfe9fffff [ 0.593422] pci 0000:00:1c.4: PREFETCH window: 0x000000c0200000-0x000000c03fffff [ 0.593619] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02 [ 0.593734] pci 0000:00:1c.5: IO window: 0xc000-0xcfff [ 0.593849] pci 0000:00:1c.5: MEM window: 0xfe800000-0xfe8fffff [ 0.593965] pci 0000:00:1c.5: PREFETCH window: 0x000000c0400000-0x000000c05fffff [ 0.594171] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 [ 0.596374] pci 0000:00:1e.0: IO window: disabled [ 0.596488] pci 0000:00:1e.0: MEM window: disabled [ 0.596600] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.596730] alloc irq_desc for 17 on node 0 [ 0.596735] alloc kstat_irqs on node 0 [ 0.596750] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.596872] pci 0000:00:1c.0: setting latency timer to 64 [ 0.596886] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.597016] pci 0000:00:1c.4: setting latency timer to 64 [ 0.597029] alloc irq_desc for 16 on node 0 [ 0.597033] alloc kstat_irqs on node 0 [ 0.597043] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.597165] pci 0000:00:1c.5: setting latency timer to 64 [ 0.597176] pci 0000:00:1e.0: setting latency timer to 64 [ 0.597185] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.597192] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff] [ 0.597199] pci_bus 0000:04: resource 0 io: [0xe000-0xefff] [ 0.597206] pci_bus 0000:04: resource 1 mem: [0xfeb00000-0xfebfffff] [ 0.597213] pci_bus 0000:04: resource 2 pref mem [0xc0000000-0xc01fffff] [ 0.597220] pci_bus 0000:03: resource 0 io: [0xd000-0xdfff] [ 0.597226] pci_bus 0000:03: resource 1 mem: [0xfe900000-0xfe9fffff] [ 0.597233] pci_bus 0000:03: resource 2 pref mem [0xc0200000-0xc03fffff] [ 0.597240] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff] [ 0.597246] pci_bus 0000:02: resource 1 mem: [0xfe800000-0xfe8fffff] [ 0.597253] pci_bus 0000:02: resource 2 pref mem [0xc0400000-0xc05fffff] [ 0.597260] pci_bus 0000:01: resource 3 io: [0x00-0xffff] [ 0.597267] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff] [ 0.597357] NET: Registered protocol family 2 [ 0.597920] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.601295] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.607815] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.608697] TCP: Hash tables configured (established 524288 bind 65536) [ 0.608825] TCP reno registered [ 0.609244] NET: Registered protocol family 1 [ 0.609553] Trying to unpack rootfs image as initramfs... [ 0.610185] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 0.642693] Freeing initrd memory: 17630k freed [ 0.662439] microcode: CPU0 sig=0x106ca, pf=0x8, revision=0x107 [ 0.662578] microcode: CPU1 sig=0x106ca, pf=0x8, revision=0x107 [ 0.662713] microcode: CPU2 sig=0x106ca, pf=0x8, revision=0x107 [ 0.662844] microcode: CPU3 sig=0x106ca, pf=0x8, revision=0x107 [ 0.663092] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba [ 0.663294] Scanning for low memory corruption every 60 seconds [ 0.664176] audit: initializing netlink socket (disabled) [ 0.664318] type=2000 audit(1699295601.663:1): initialized [ 0.680233] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.688525] VFS: Disk quotas dquot_6.5.2 [ 0.688886] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.692626] Installing knfsd (copyright (C) 1996 [email protected]). [ 0.693093] NTFS driver 2.1.29 [Flags: R/W]. [ 0.693734] fuse init (API version 7.12) [ 0.694366] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 0.696896] SGI XFS Quota Management subsystem [ 0.697059] msgmni has been set to 7909 [ 0.697582] SELinux: Registering netfilter hooks [ 0.698846] alg: No test for stdrng (krng) [ 0.698979] async_tx: api initialized (sync-only) [ 0.699562] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.699760] io scheduler noop registered [ 0.699867] io scheduler anticipatory registered [ 0.699991] io scheduler deadline registered [ 0.700307] io scheduler cfq registered (default) [ 0.700440] pci 0000:00:02.0: Boot video device [ 0.700931] alloc irq_desc for 24 on node 0 [ 0.700937] alloc kstat_irqs on node 0 [ 0.700971] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X [ 0.700985] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.701539] alloc irq_desc for 25 on node 0 [ 0.701544] alloc kstat_irqs on node 0 [ 0.701559] pcieport-driver 0000:00:1c.4: irq 25 for MSI/MSI-X [ 0.701571] pcieport-driver 0000:00:1c.4: setting latency timer to 64 [ 0.702113] alloc irq_desc for 26 on node 0 [ 0.702119] alloc kstat_irqs on node 0 [ 0.702132] pcieport-driver 0000:00:1c.5: irq 26 for MSI/MSI-X [ 0.702145] pcieport-driver 0000:00:1c.5: setting latency timer to 64 [ 0.702793] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.703186] Initializing ths8200_init [ 0.703414] Initializing dove_adi9889_init [ 0.704301] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.704507] ACPI: Power Button [PWRF] [ 0.704879] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 0.705103] ACPI: Power Button [PWRB] [ 0.706135] processor LNXCPU:00: registered as cooling_device0 [ 0.706825] processor LNXCPU:01: registered as cooling_device1 [ 0.707606] processor LNXCPU:02: registered as cooling_device2 [ 0.708316] processor LNXCPU:03: registered as cooling_device3 [ 0.728242] Non-volatile memory driver v1.3 [ 0.728360] Linux agpgart interface v0.103 [ 0.728588] agpgart-intel 0000:00:00.0: Intel IGD Chipset [ 0.729069] agpgart-intel 0000:00:00.0: detected 8188K stolen memory [ 0.732747] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.733216] [drm] Initialized drm 1.1.0 20060810 [ 0.733460] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.733583] i915 0000:00:02.0: setting latency timer to 64 [ 0.764287] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining [ 0.764494] [drm] MTRR allocation failed. Graphics performance may suffer. [ 0.764985] alloc irq_desc for 27 on node 0 [ 0.764992] alloc kstat_irqs on node 0 [ 0.765009] i915 0000:00:02.0: irq 27 for MSI/MSI-X [ 0.903594] [drm] Big FIFO is enabled [ 0.965891] [drm] Big FIFO is enabled [ 0.965901] [drm] DAC-6: set mode 1920x1080 17 [ 0.965963] [drm] Big FIFO is enabled [ 0.965977] [drm] Big FIFO is enabled [ 1.038408] Console: switching to colour frame buffer device 240x67 [ 1.058969] Switched to high resolution mode on CPU 3 [ 1.059136] Switched to high resolution mode on CPU 2 [ 1.059307] Switched to high resolution mode on CPU 1 [ 1.059829] Switched to high resolution mode on CPU 0 [ 1.065121] [drm] fb0: inteldrmfb frame buffer device [ 1.065447] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 1.065614] work_for_cpu used greatest stack depth: 3648 bytes left [ 1.065904] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.310123] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.554125] serial8250: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A [ 1.555318] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.555852] 00:07: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A [ 1.562269] brd: module loaded [ 1.565496] loop: module loaded [ 1.566433] ahci 0000:00:1f.2: version 3.0 [ 1.566460] alloc irq_desc for 19 on node 0 [ 1.566466] alloc kstat_irqs on node 0 [ 1.566482] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.566679] ** BUFFALO Disable Command Queuing Function [ahci 0000:00:1f.2] ** [ 1.566850] alloc irq_desc for 28 on node 0 [ 1.566855] alloc kstat_irqs on node 0 [ 1.566869] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X [ 1.566879] ahci 0000:00:1f.2: controller can't do NCQ, turning off CAP_NCQ [ 1.567097] ahci: SSS flag set, parallel bus scan disabled [ 1.567267] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 1.567443] ahci 0000:00:1f.2: flags: 64bit sntf stag pm led clo pio slum part ems [ 1.567606] ahci 0000:00:1f.2: setting latency timer to 64 [ 1.577190] scsi0 : ahci [ 1.577806] scsi1 : ahci [ 1.578271] scsi2 : ahci [ 1.578701] scsi3 : ahci [ 1.579137] scsi4 : ahci [ 1.579565] scsi5 : ahci [ 1.580237] ata1: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafb900 irq 28 [ 1.580406] ata2: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafb980 irq 28 [ 1.580561] ata3: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafba00 irq 28 [ 1.580714] ata4: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafba80 irq 28 [ 1.580868] ata5: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafbb00 irq 28 [ 1.581032] ata6: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafbb80 irq 28 [ 1.581728] sata_mv 0000:04:00.0: version 1.28 [ 1.581870] ** BUFFALO Disable Command Queuing Function [sata_mv 0000:04:00.0] ** [ 1.582070] sata_mv 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.582420] sata_mv 0000:04:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx [ 1.582583] sata_mv 0000:04:00.0: setting latency timer to 64 [ 1.583308] scsi6 : sata_mv [ 1.583767] scsi7 : sata_mv [ 1.584186] scsi8 : sata_mv [ 1.584587] scsi9 : sata_mv [ 1.584908] ata7: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb22000 irq 16 [ 1.588089] ata8: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb24000 irq 16 [ 1.591289] ata9: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb26000 irq 16 [ 1.594479] ata10: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb28000 irq 16 [ 1.598966] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI [ 1.602383] Copyright (c) 1999-2006 Intel Corporation. [ 1.605995] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 [ 1.609580] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 1.613542] sk98lin 0000:03:00.0: enabling device (0000 -> 0003) [ 1.617310] sk98lin 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.621157] sk98lin: Network Device Driver v10.85.9.3 [ 1.621160] (C)Copyright 1999-2010 Marvell(R). [ 1.628990] sk98lin 0000:03:00.0: setting latency timer to 64 [ 1.630780] eth0: Generic Marvell Yukon chipset Ethernet device [ 1.635087] sk98lin 0000:02:00.0: enabling device (0000 -> 0003) [ 1.639262] sk98lin 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.643544] sk98lin 0000:02:00.0: setting latency timer to 64 [ 1.645380] eth1: Generic Marvell Yukon chipset Ethernet device [ 1.650424] PNP: No PS/2 controller found. Probing ports directly. [ 1.655437] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.659953] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.664730] mice: PS/2 mouse device common for all mice [ 1.670754] rtc_cmos 00:03: RTC can wake from S4 [ 1.675653] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.680474] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 1.685605] md: raid0 personality registered for level 0 [ 1.690592] md: raid1 personality registered for level 1 [ 1.695512] md: raid6 personality registered for level 6 [ 1.700438] md: raid5 personality registered for level 5 [ 1.705329] md: raid4 personality registered for level 4 [ 1.710953] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected] [ 1.716777] cpuidle: using governor ladder [ 1.721781] cpuidle: using governor menu [ 1.726954] Kernel event proc (C) BUFFALO INC. V.1.00 installed. [ 1.731904] MICON ctrl (C) BUFFALO INC. V.1.00 installed. [ 1.736812] UPSDRV (C) BUFFALO INC. V.1.00 installed. [ 1.741705] OMRON contact type ups shutdown support enabled! [ 1.746609] [hdd control module init proc] [ 1.751562] buffalo/gpio directory create successful..... [ 1.756520] hotplug directory create successful..... [ 1.761536] HDD0_PRESENT_STATUS_FILE create successful..... [ 1.766582] HDD1_PRESENT_STATUS_FILE create successful..... [ 1.771583] HDD2_PRESENT_STATUS_FILE create successful..... [ 1.776490] HDD3_PRESENT_STATUS_FILE create successful..... [ 1.781294] HDD4_PRESENT_STATUS_FILE create successful..... [ 1.786008] HDD5_PRESENT_STATUS_FILE create successful..... [ 1.790631] HDD6_PRESENT_STATUS_FILE create successful..... [ 1.795145] HDD7_PRESENT_STATUS_FILE create successful..... [ 1.799576] power_control directory create successful..... [ 1.803968] HDD0_POWER_STATUS_FILE create successful..... [ 1.808428] HDD1_POWER_STATUS_FILE create successful..... [ 1.812887] HDD2_POWER_STATUS_FILE create successful..... [ 1.817352] HDD3_POWER_STATUS_FILE create successful..... [ 1.821813] HDD4_POWER_STATUS_FILE create successful..... [ 1.826280] HDD5_POWER_STATUS_FILE create successful..... [ 1.830646] HDD6_POWER_STATUS_FILE create successful..... [ 1.835011] HDD7_POWER_STATUS_FILE create successful..... [ 1.839370] hdd control module 0.2 initialized... [ 1.843818] buffalo/gpio/switch directory create successful..... [ 1.848339] buffalo/gpio/switch/func create successful..... [ 1.852900] buffalo/gpio/switch/display create successful..... [ 1.857405] enter fan module init [ 1.862143] enter cmos module init [ 1.866752] Netfilter messages via NETLINK v0.30. [ 1.872020] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.876384] TCP cubic registered [ 1.880750] NET: Registered protocol family 17 [ 1.885455] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.886108] RPC: Registered udp transport module. [ 1.886114] RPC: Registered tcp transport module. [ 1.886800] PM: Resume from disk failed. [ 1.886835] registered taskstats version 1 [ 1.887109] Magic number: 15:420:594 [ 2.052451] ata1.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100 [ 2.056942] ata1.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.062123] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.063066] ata1.00: configured for UDMA/100 [ 2.074366] scsi 0:0:0:0: Direct-Access ATA MG04ACA600E FS3J PQ: 0 ANSI: 5 [ 2.079789] sd 0:0:0:0: [sda] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 2.079968] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.088975] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 2.093670] sd 0:0:0:0: [sda] Write Protect is off [ 2.098195] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.098288] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.103312] sda: sda1 sda9 [ 2.366780] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.409078] ata7.00: ATA-8: TOSHIBA MG04ACA600E, FS3B, max UDMA/100 [ 2.413636] ata7.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.427105] ata7.00: configured for UDMA/100 [ 2.813030] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.834479] ata2.00: ATA-8: TOSHIBA MG04ACA600E, FS4B, max UDMA/100 [ 2.839202] ata2.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 2.845527] ata2.00: configured for UDMA/100 [ 2.861219] scsi 1:0:0:0: Direct-Access ATA TOSHIBA MG04ACA6 FS4B PQ: 0 ANSI: 5 [ 2.866766] sd 1:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 2.867801] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 2.876626] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 2.881721] sd 1:0:0:0: [sdb] Write Protect is off [ 2.886672] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.886753] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.892218] sdb: sdb1 sdb9 [ 2.953795] sd 1:0:0:0: [sdb] Attached SCSI disk [ 3.590032] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.737478] ata3.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100 [ 3.742515] ata3.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 3.749148] ata3.00: configured for UDMA/100 [ 3.765227] scsi 2:0:0:0: Direct-Access ATA MG04ACA600E FS3J PQ: 0 ANSI: 5 [ 3.770989] sd 2:0:0:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 3.771286] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 3.781299] sd 2:0:0:0: [sdc] 4096-byte physical blocks [ 3.786530] sd 2:0:0:0: [sdc] Write Protect is off [ 3.791649] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 [ 3.791732] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.797422] sdc: sdc1 sdc9 [ 4.058762] sd 2:0:0:0: [sdc] Attached SCSI disk [ 4.494031] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 4.644001] ata4.00: ATA-8: TOSHIBA MG04ACA600E, FS4B, max UDMA/100 [ 4.649549] ata4.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 4.656804] ata4.00: configured for UDMA/100 [ 4.673234] scsi 3:0:0:0: Direct-Access ATA TOSHIBA MG04ACA6 FS4B PQ: 0 ANSI: 5 [ 4.679668] sd 3:0:0:0: [sdd] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 4.679926] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 4.691353] sd 3:0:0:0: [sdd] 4096-byte physical blocks [ 4.697403] sd 3:0:0:0: [sdd] Write Protect is off [ 4.703358] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00 [ 4.703438] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 4.709954] sdd: sdd1 sdd9 [ 4.985031] ata5: SATA link down (SStatus 0 SControl 300) [ 4.996521] sd 3:0:0:0: [sdd] Attached SCSI disk [ 5.305026] ata6: SATA link down (SStatus 0 SControl 300) [ 5.322231] scsi 6:0:0:0: Direct-Access ATA TOSHIBA MG04ACA6 FS3B PQ: 0 ANSI: 5 [ 5.329310] sd 6:0:0:0: [sde] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 5.329574] sd 6:0:0:0: Attached scsi generic sg4 type 0 [ 5.342274] sd 6:0:0:0: [sde] 4096-byte physical blocks [ 5.348831] sd 6:0:0:0: [sde] Write Protect is off [ 5.355233] sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00 [ 5.355316] sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.362228] sde: sde1 sde9 [ 5.629998] sd 6:0:0:0: [sde] Attached SCSI disk [ 5.787063] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 5.948070] ata8.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100 [ 5.954526] ata8.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 5.970100] ata8.00: configured for UDMA/100 [ 5.976850] scsi 7:0:0:0: Direct-Access ATA MG04ACA600E FS3J PQ: 0 ANSI: 5 [ 5.984298] sd 7:0:0:0: [sdf] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 5.984587] sd 7:0:0:0: Attached scsi generic sg5 type 0 [ 5.997720] sd 7:0:0:0: [sdf] 4096-byte physical blocks [ 6.004498] sd 7:0:0:0: [sdf] Write Protect is off [ 6.011073] sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00 [ 6.011153] sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.018193] sdf: sdf1 sdf9 [ 6.278905] sd 7:0:0:0: [sdf] Attached SCSI disk [ 6.443050] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 6.585068] ata9.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100 [ 6.591719] ata9.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 6.607101] ata9.00: configured for UDMA/100 [ 6.613876] scsi 8:0:0:0: Direct-Access ATA MG04ACA600E FS3J PQ: 0 ANSI: 5 [ 6.621226] sd 8:0:0:0: [sdg] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 6.621543] sd 8:0:0:0: Attached scsi generic sg6 type 0 [ 6.634721] sd 8:0:0:0: [sdg] 4096-byte physical blocks [ 6.641515] sd 8:0:0:0: [sdg] Write Protect is off [ 6.648105] sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00 [ 6.648184] sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 6.655297] sdg: sdg1 sdg9 [ 6.914987] sd 8:0:0:0: [sdg] Attached SCSI disk [ 7.081049] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7.242066] ata10.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100 [ 7.248654] ata10.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 7.264101] ata10.00: configured for UDMA/100 [ 7.270881] scsi 9:0:0:0: Direct-Access ATA MG04ACA600E FS3J PQ: 0 ANSI: 5 [ 7.278262] sd 9:0:0:0: [sdh] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB) [ 7.285038] sd 9:0:0:0: [sdh] 4096-byte physical blocks [ 7.285746] sd 9:0:0:0: Attached scsi generic sg7 type 0 [ 7.298524] sd 9:0:0:0: [sdh] Write Protect is off [ 7.305102] sd 9:0:0:0: [sdh] Mode Sense: 00 3a 00 00 [ 7.305193] sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.312298] sdh: sdh1 sdh9 [ 7.570863] sd 9:0:0:0: [sdh] Attached SCSI disk [ 7.577532] md: Waiting for all devices to be available before autodetect [ 7.584192] md: If you don't use raid, use raid=noautodetect [ 7.591304] md: Autodetecting RAID arrays. [ 7.597843] md: Scanned 0 and added 0 devices. [ 7.604368] md: autorun ... [ 7.610873] md: ... autorun DONE. [ 7.617396] RAMDISK: gzip image found at block 0 [ 8.925136] VFS: Mounted root (ext2 filesystem) on device 1:0. [ 9.040492] bootver=BOOTVER=Unkown [ 9.046936] buffalo_series_name=TeraStation [ 9.053299] buffalo_product_name=TS-QVHL/R5(SAIMEI) [ 11.391793] usbcore: registered new interface driver usbfs [ 11.397784] usbcore: registered new interface driver hub [ 11.403595] usbcore: registered new device driver usb [ 11.423642] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.429332] alloc irq_desc for 23 on node 0 [ 11.429339] alloc kstat_irqs on node 0 [ 11.429355] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 11.434977] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 11.434985] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 11.440584] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 11.450031] ehci_hcd 0000:00:1d.7: debug port 1 [ 11.455499] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 11.455536] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfeafb400 [ 11.470023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 11.475448] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.480820] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.486164] usb usb1: Product: EHCI Host Controller [ 11.491508] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd [ 11.496905] usb usb1: SerialNumber: 0000:00:1d.7 [ 11.502491] usb usb1: configuration #1 chosen from 1 choice [ 11.507948] hub 1-0:1.0: USB hub found [ 11.513261] hub 1-0:1.0: 6 ports detected [ 11.526327] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 11.539085] uhci_hcd: USB Universal Host Controller Interface driver [ 11.544749] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 11.550071] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 11.550079] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 11.555333] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 11.560599] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ac00 [ 11.565858] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.571102] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.576361] usb usb2: Product: UHCI Host Controller [ 11.581571] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 11.586743] usb usb2: SerialNumber: 0000:00:1d.0 [ 11.592161] usb usb2: configuration #1 chosen from 1 choice [ 11.597476] hub 2-0:1.0: USB hub found [ 11.602586] hub 2-0:1.0: 2 ports detected [ 11.608000] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 11.613188] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 11.613196] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 11.618401] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 11.623665] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000 [ 11.628942] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.634155] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.639358] usb usb3: Product: UHCI Host Controller [ 11.644569] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 11.649798] usb usb3: SerialNumber: 0000:00:1d.1 [ 11.655209] usb usb3: configuration #1 chosen from 1 choice [ 11.660575] hub 3-0:1.0: USB hub found [ 11.665770] hub 3-0:1.0: 2 ports detected [ 11.671281] alloc irq_desc for 18 on node 0 [ 11.671287] alloc kstat_irqs on node 0 [ 11.671303] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 11.676552] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 11.676559] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 11.681735] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 11.686915] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b080 [ 11.692182] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 11.697475] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.702852] usb usb4: Product: UHCI Host Controller [ 11.708299] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 11.713827] usb usb4: SerialNumber: 0000:00:1d.2 [ 11.719710] usb usb4: configuration #1 chosen from 1 choice [ 11.725531] hub 4-0:1.0: USB hub found [ 11.731171] hub 4-0:1.0: 2 ports detected [ 11.743104] usbcore: registered new interface driver libusual [ 11.759730] Initializing USB Mass Storage driver... [ 11.765622] usbcore: registered new interface driver usb-storage [ 11.771354] USB Mass Storage support registered. [ 11.784400] usbcore: registered new interface driver usblp [ 11.802255] usbcore: registered new interface driver hiddev [ 11.808042] usbcore: registered new interface driver usbhid [ 11.813606] usbhid: v2.6:USB HID core driver [ 11.872039] usb 1-2: new high speed USB device using ehci_hcd and address 3 [ 11.992053] usb 1-2: New USB device found, idVendor=346d, idProduct=5678 [ 11.997632] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.003181] usb 1-2: Product: Disk 20 [ 12.008739] usb 1-2: Manufacturer: USB [ 12.014284] usb 1-2: SerialNumber: FC16684F50E61 [ 12.020144] usb 1-2: configuration #1 chosen from 1 choice [ 12.026394] scsi10 : SCSI emulation for USB Mass Storage devices [ 12.032392] usb-storage: device found at 3 [ 12.032399] usb-storage: waiting for device to settle before scanning [ 12.238029] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 12.413672] usb 2-1: New USB device found, idVendor=0518, idProduct=0001 [ 12.419311] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.424919] usb 2-1: Product: USB-compliant keyboard [ 12.430531] usb 2-1: Manufacturer: Plus More Enterprise LTD. [ 12.436436] usb 2-1: configuration #1 chosen from 1 choice [ 12.460412] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input2 [ 12.466677] generic-usb 0003:0518:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0 [ 12.489485] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input3 [ 12.496212] generic-usb 0003:0518:0001.0002: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1 [ 17.032706] scsi 10:0:0:0: Direct-Access VendorC ProductCode 2.00 PQ: 0 ANSI: 4 [ 17.040392] sd 10:0:0:0: Attached scsi generic sg8 type 0 [ 17.047200] sd 10:0:0:0: [sdi] 61440000 512-byte logical blocks: (31.4 GB/29.2 GiB) [ 17.048155] usb-storage: device scan complete [ 17.054539] sd 10:0:0:0: [sdi] Write Protect is off [ 17.061198] sd 10:0:0:0: [sdi] Mode Sense: 03 00 00 00 [ 17.061205] sd 10:0:0:0: [sdi] Assuming drive cache: write through [ 17.070154] sd 10:0:0:0: [sdi] Assuming drive cache: write through [ 17.076756] sdi: sdi1 [ 17.085781] sd 10:0:0:0: [sdi] Assuming drive cache: write through [ 17.092380] sd 10:0:0:0: [sdi] Attached SCSI removable disk [ 18.111401] usbcore: deregistering interface driver usbhid [ 18.155992] usbcore: deregistering interface driver hiddev [ 18.171143] usbcore: deregistering interface driver usblp [ 18.184404] usbcore: deregistering interface driver usb-storage [ 18.197397] usbcore: deregistering interface driver libusual [ 18.212060] uhci_hcd 0000:00:1d.2: remove, state 4 [ 18.218253] usb usb4: USB disconnect, address 1 [ 18.225079] uhci_hcd 0000:00:1d.2: USB bus 4 deregistered [ 18.231270] uhci_hcd 0000:00:1d.2: PCI INT C disabled [ 18.237386] uhci_hcd 0000:00:1d.1: remove, state 4 [ 18.243467] usb usb3: USB disconnect, address 1 [ 18.250158] uhci_hcd 0000:00:1d.1: USB bus 3 deregistered [ 18.256306] uhci_hcd 0000:00:1d.1: PCI INT B disabled [ 18.262363] uhci_hcd 0000:00:1d.0: remove, state 1 [ 18.268378] usb usb2: USB disconnect, address 1 [ 18.274358] usb 2-1: USB disconnect, address 2 [ 18.281720] uhci_hcd 0000:00:1d.0: USB bus 2 deregistered [ 18.287721] uhci_hcd 0000:00:1d.0: PCI INT A disabled [ 18.309431] ehci_hcd 0000:00:1d.7: remove, state 1 [ 18.315315] usb usb1: USB disconnect, address 1 [ 18.321145] usb 1-2: USB disconnect, address 3 [ 18.332186] ehci_hcd 0000:00:1d.7: USB bus 1 deregistered [ 18.338111] ehci_hcd 0000:00:1d.7: PCI INT A disabled [ 18.354405] usbcore: deregistering device driver usb [ 18.360431] usbcore: deregistering interface driver usbfs [ 18.366512] usbcore: deregistering interface driver hub [ 18.543168] md: md0 stopped. [ 18.558210] md: md1 stopped. [ 18.572272] md: md2 stopped. [ 18.602824] Freeing unused kernel memory: 548k freed [ 18.608710] Write protecting the kernel read-only data: 7448k [ 102.256900] AC Power Loss is 2 [ 107.883671] alloc irq_desc for 29 on node 0 [ 107.883679] alloc kstat_irqs on node 0 [ 107.883703] sk98lin 0000:03:00.0: irq 29 for MSI/MSI-X [ 110.601306] eth1: network connection up using port A [ 110.601306] interrupt src: MSI [ 110.601306] speed: 1000 [ 110.601306] autonegotiation: yes [ 110.601306] duplex mode: full [ 110.601306] flowctrl: symmetric [ 110.601306] role: slave [ 110.601306] tcp offload: enabled [ 110.601306] scatter-gather: enabled [ 110.601306] tx-checksum: enabled [ 110.601306] rx-checksum: enabled [ 110.601306] rx-polling: enabled [ 111.906444] alloc irq_desc for 30 on node 0 [ 111.906452] alloc kstat_irqs on node 0 [ 111.906476] sk98lin 0000:02:00.0: irq 30 for MSI/MSI-X [ 148.827790] usbcore: registered new interface driver usbfs [ 148.833115] usbcore: registered new interface driver hub [ 148.844425] usbcore: registered new device driver usb [ 148.868503] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 148.879326] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 148.884629] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 148.884643] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 148.890000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 148.899300] ehci_hcd 0000:00:1d.7: debug port 1 [ 148.904537] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 148.904580] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfeafb400 [ 148.920050] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 148.925437] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 148.930854] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 148.935566] usb usb1: Product: EHCI Host Controller [ 148.940890] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd [ 148.945288] usb usb1: SerialNumber: 0000:00:1d.7 [ 148.956543] usb usb1: configuration #1 chosen from 1 choice [ 148.958499] hub 1-0:1.0: USB hub found [ 148.958528] hub 1-0:1.0: 6 ports detected [ 148.988655] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 149.006477] uhci_hcd: USB Universal Host Controller Interface driver [ 149.016076] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 149.022203] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 149.022216] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 149.028773] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 149.034266] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ac00 [ 149.039472] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 149.045152] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 149.050723] usb usb2: Product: UHCI Host Controller [ 149.056292] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 149.062223] usb usb2: SerialNumber: 0000:00:1d.0 [ 149.071683] usb usb2: configuration #1 chosen from 1 choice [ 149.081702] hub 2-0:1.0: USB hub found [ 149.086566] hub 2-0:1.0: 2 ports detected [ 149.096302] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 149.101416] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 149.101424] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 149.106946] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 149.112531] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000 [ 149.118377] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 149.124235] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 149.129814] usb usb3: Product: UHCI Host Controller [ 149.135417] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 149.142226] usb usb3: SerialNumber: 0000:00:1d.1 [ 149.148877] usb usb3: configuration #1 chosen from 1 choice [ 149.155691] hub 3-0:1.0: USB hub found [ 149.161187] hub 3-0:1.0: 2 ports detected [ 149.167188] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 149.172781] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 149.172791] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 149.178314] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 149.183758] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b080 [ 149.189284] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 149.194684] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 149.200127] usb usb4: Product: UHCI Host Controller [ 149.205542] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 149.211000] usb usb4: SerialNumber: 0000:00:1d.2 [ 149.216755] usb usb4: configuration #1 chosen from 1 choice [ 149.222394] hub 4-0:1.0: USB hub found [ 149.227803] hub 4-0:1.0: 2 ports detected [ 149.239651] usbcore: registered new interface driver libusual [ 149.256810] Initializing USB Mass Storage driver... [ 149.262584] usbcore: registered new interface driver usb-storage [ 149.268261] USB Mass Storage support registered. [ 149.284149] usbcore: registered new interface driver usblp [ 149.302034] usbcore: registered new interface driver hiddev [ 149.308256] usbcore: registered new interface driver usbhid [ 149.314124] usbhid: v2.6:USB HID core driver [ 149.325312] usb 1-2: new high speed USB device using ehci_hcd and address 3 [ 149.447042] usb 1-2: New USB device found, idVendor=346d, idProduct=5678 [ 149.452752] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 149.459239] usb 1-2: Product: Disk 20 [ 149.465213] usb 1-2: Manufacturer: USB [ 149.465221] usb 1-2: SerialNumber: FC16684F50E61 [ 149.465661] usb 1-2: configuration #1 chosen from 1 choice [ 149.466369] scsi11 : SCSI emulation for USB Mass Storage devices [ 149.466838] usb-storage: device found at 3 [ 149.466845] usb-storage: waiting for device to settle before scanning [ 149.569084] usb 2-1: new low speed USB device using uhci_hcd and address 2 [ 149.747319] usb 2-1: New USB device found, idVendor=0518, idProduct=0001 [ 149.754561] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 149.761784] usb 2-1: Product: USB-compliant keyboard [ 149.768261] usb 2-1: Manufacturer: Plus More Enterprise LTD. [ 149.774247] usb 2-1: configuration #1 chosen from 1 choice [ 149.798056] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input4 [ 149.805236] generic-usb 0003:0518:0001.0003: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0 [ 149.828136] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input5 [ 149.828714] generic-usb 0003:0518:0001.0004: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1 [ 150.188391] set AC Power Loss to 0 [ 154.466703] scsi 11:0:0:0: Direct-Access VendorC ProductCode 2.00 PQ: 0 ANSI: 4 [ 154.476423] sd 11:0:0:0: Attached scsi generic sg8 type 0 [ 154.483718] sd 11:0:0:0: [sdi] 61440000 512-byte logical blocks: (31.4 GB/29.2 GiB) [ 154.492791] sd 11:0:0:0: [sdi] Write Protect is off [ 154.501273] sd 11:0:0:0: [sdi] Mode Sense: 03 00 00 00 [ 154.501284] sd 11:0:0:0: [sdi] Assuming drive cache: write through [ 154.503593] usb-storage: device scan complete [ 154.510517] sd 11:0:0:0: [sdi] Assuming drive cache: write through [ 154.517080] sdi: sdi1 [ 154.526427] sd 11:0:0:0: [sdi] Assuming drive cache: write through [ 154.533209] sd 11:0:0:0: [sdi] Attached SCSI removable disk