Specs

 

CPU Intel Atom D510 1.66GHz Dual-Core (64-bit)
Memory 2 GB DDR2 (Upgradable to 4GB)
Bays 8
Network 2x 10/100/1000 Mbps (Marvell 88e8059)
Sata 8x SATA II (Intel 82801ir and Marvell 88SX7042)
USB 2.0 2x Back
USB 3.0 No
Serial port 1x Back
VGA Yes
Fan 2x
Power Internal AC 100-240V, universal 50/60Hz

Stock Firmware Installation

You can re-install the linux-based firmware by creating a recovery disk, see Create Recovery Disk for Intel-based Terastation You can then boot from it by switching the boot mode switch on the back to "USB", after a few minutes the device will go into EM Mode Then you can install the firmware using the firmware updater in debug mode, see Enable Debug mode for LSUpdater/TSUpdater

Custom Firmware/Operating System installation

These devices run on an Intel Atom processor with a fairly typical BIOS and include a VGA out and support USB keyboards, you should be able to run virtually any operating system that will run on a normal PC depending on drivers/etc.

For tools to help install and configure Debian on these devices, see Installing Debian on Intel Terastations

Pictures

DMESG output

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.31.8-atom_d510 (root@HP7907) (gcc version 4.2.0 20070413 (prerelease)) #2 SMP Wed Dec 22 12:29:42 JST 2021
[    0.000000] Command line: root=sde1 rw usbboot=yes mode=initilize ts4000=no acc=no
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   Centaur CentaurHauls
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000400 - 000000000009e800 (usable)
[    0.000000]  BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000bf580000 (usable)
[    0.000000]  BIOS-e820: 00000000bf580000 - 00000000bf58e000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000bf5d0000 - 00000000bf5e0000 (reserved)
[    0.000000]  BIOS-e820: 00000000bf5e7000 - 00000000c0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] e820 update range: 0000000000100000 - 0000000000100030 (usable) ==> (usable)
[    0.000000] extended physical RAM map:
[    0.000000]  reserve setup_data: 0000000000000400 - 000000000009e800 (usable)
[    0.000000]  reserve setup_data: 000000000009e800 - 00000000000a0000 (reserved)
[    0.000000]  reserve setup_data: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  reserve setup_data: 0000000000100000 - 0000000000100030 (usable)
[    0.000000]  reserve setup_data: 0000000000100030 - 00000000bf580000 (usable)
[    0.000000]  reserve setup_data: 00000000bf580000 - 00000000bf58e000 (ACPI data)
[    0.000000]  reserve setup_data: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS)
[    0.000000]  reserve setup_data: 00000000bf5d0000 - 00000000bf5e0000 (reserved)
[    0.000000]  reserve setup_data: 00000000bf5e7000 - 00000000c0000000 (reserved)
[    0.000000]  reserve setup_data: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  reserve setup_data: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  reserve setup_data: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] DMI present.
[    0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-D7FFF write-protect
[    0.000000]   D8000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F00000000 write-back
[    0.000000]   1 base 100000000 mask FC0000000 write-back
[    0.000000]   2 base 0C0000000 mask FC0000000 uncachable
[    0.000000]   3 base 0BF600000 mask FFFF00000 write-through
[    0.000000]   4 base 0BF700000 mask FFFF00000 uncachable
[    0.000000]   5 base 0BF800000 mask FFF800000 uncachable
[    0.000000]   6 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x407050600070106, new 0x7010600070106
[    0.000000] last_pfn = 0xbf580 max_arch_pfn = 0x400000000
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000400 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009e800 (usable)
[    0.000000]  modified: 000000000009e800 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 0000000000100030 (usable)
[    0.000000]  modified: 0000000000100030 - 00000000bf580000 (usable)
[    0.000000]  modified: 00000000bf580000 - 00000000bf58e000 (ACPI data)
[    0.000000]  modified: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS)
[    0.000000]  modified: 00000000bf5d0000 - 00000000bf5e0000 (reserved)
[    0.000000]  modified: 00000000bf5e7000 - 00000000c0000000 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000]  modified: 0000000100000000 - 0000000140000000 (usable)
[    0.000000] initial memory mapped : 0 - 20000000
[    0.000000] init_memory_mapping: 0000000000000000-00000000bf580000
[    0.000000]  0000000000 - 00bf400000 page 2M
[    0.000000]  00bf400000 - 00bf580000 page 4k
[    0.000000] kernel direct mapping tables up to bf580000 @ 10000-15000
[    0.000000] init_memory_mapping: 0000000100000000-0000000140000000
[    0.000000]  0100000000 - 0140000000 page 2M
[    0.000000] kernel direct mapping tables up to 140000000 @ 13000-19000
[    0.000000] RAMDISK: 7eebf000 - 7fff6855
[    0.000000] ACPI: RSDP 00000000000f9f30 00024 (v02 ACPIAM)
[    0.000000] ACPI: XSDT 00000000bf580100 00054 (v01 MATSU  SLIC1108 20101228 MSFT 00000097)
[    0.000000] ACPI: FACP 00000000bf580290 000F4 (v04 122810 FACP0918 20101228 MSFT 00000097)
[    0.000000] ACPI: DSDT 00000000bf5805c0 05CE6 (v02  WSQVL WSQVL301 00000301 INTL 20051117)
[    0.000000] ACPI: FACS 00000000bf58e000 00040
[    0.000000] ACPI: APIC 00000000bf580390 0006C (v02 122810 APIC0918 20101228 MSFT 00000097)
[    0.000000] ACPI: MCFG 00000000bf580400 0003C (v01 122810 OEMMCFG  20101228 MSFT 00000097)
[    0.000000] ACPI: SLIC 00000000bf580440 00176 (v01 MATSU  SLIC1108 20101228 MSFT 00000097)
[    0.000000] ACPI: OEMB 00000000bf58e040 00082 (v01 122810 OEMB0918 20101228 MSFT 00000097)
[    0.000000] ACPI: GSCI 00000000bf58e0d0 02024 (v01 122810 GMCHSCI  20101228 MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] No NUMA configuration found
[    0.000000] Faking a node at 0000000000000000-0000000140000000
[    0.000000] Bootmem setup node 0 0000000000000000-0000000140000000
[    0.000000]   NODE_DATA [0000000000014000 - 0000000000018fff]
[    0.000000]   bootmap [0000000000019000 -  0000000000040fff] pages 28
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 0140000000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
[    0.000000]   #2 [0001000000 - 0001933734]    TEXT DATA BSS ==> [0001000000 - 0001933734]
[    0.000000]   #3 [007eebf000 - 007fff6855]          RAMDISK ==> [007eebf000 - 007fff6855]
[    0.000000]   #4 [000009e800 - 0000100000]    BIOS reserved ==> [000009e800 - 0000100000]
[    0.000000]   #5 [0000100000 - 0000100030]     setup data 9 ==> [0000100000 - 0000100030]
[    0.000000]   #6 [0001934000 - 000193420f]              BRK ==> [0001934000 - 000193420f]
[    0.000000]   #7 [0000010000 - 0000013000]          PGTABLE ==> [0000010000 - 0000013000]
[    0.000000]   #8 [0000013000 - 0000014000]          PGTABLE ==> [0000013000 - 0000014000]
[    0.000000] found SMP MP-table at [ffff8800000ff780] ff780
[    0.000000]  [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880028600000-ffff88002bdfffff] on node 0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   DMA32    0x00001000 -> 0x00100000
[    0.000000]   Normal   0x00100000 -> 0x00140000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009e
[    0.000000]     0: 0x00000101 -> 0x000bf580
[    0.000000]     0: 0x00100000 -> 0x00140000
[    0.000000] On node 0 totalpages: 1045773
[    0.000000]   DMA zone: 56 pages used for memmap
[    0.000000]   DMA zone: 104 pages reserved
[    0.000000]   DMA zone: 3821 pages, LIFO batch:0
[    0.000000]   DMA32 zone: 14280 pages used for memmap
[    0.000000]   DMA32 zone: 765368 pages, LIFO batch:31
[    0.000000]   Normal zone: 3584 pages used for memmap
[    0.000000]   Normal zone: 258560 pages, LIFO batch:31
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[    0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[    0.000000] nr_irqs_gsi: 24
[    0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[    0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[    0.000000] PM: Registered nosave memory: 0000000000100000 - 0000000000101000
[    0.000000] PM: Registered nosave memory: 00000000bf580000 - 00000000bf58e000
[    0.000000] PM: Registered nosave memory: 00000000bf58e000 - 00000000bf5d0000
[    0.000000] PM: Registered nosave memory: 00000000bf5d0000 - 00000000bf5e0000
[    0.000000] PM: Registered nosave memory: 00000000bf5e0000 - 00000000bf5e7000
[    0.000000] PM: Registered nosave memory: 00000000bf5e7000 - 00000000c0000000
[    0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000
[    0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[    0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000
[    0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000
[    0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ee00000)
[    0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 28 pages at ffff880028022000, static data 82848 bytes
[    0.000000] Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1027749
[    0.000000] Policy zone: Normal
[    0.000000] Kernel command line: root=sde1 rw usbboot=yes mode=initilize ts4000=no acc=no
[    0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Checking aperture...
[    0.000000] No AGP bridge found
[    0.000000] Calgary: detecting Calgary via BIOS EBDA area
[    0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[    0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[    0.000000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000
[    0.000000] software IO TLB at phys 0x20000000 - 0x24000000
[    0.000000] Memory: 4032052k/5242880k available (5097k kernel code, 1059788k absent, 151040k reserved, 2891k data, 548k init)
[    0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:4352 nr_irqs:440
[    0.000000] Extended CMOS year: 2000
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1662.838 MHz processor.
[    0.000999] Console: colour EGA 80x25
[    0.000999] console [tty0] enabled
[    0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.67 BogoMIPS (lpj=1662838)
[    0.000999] Security Framework initialized
[    0.000999] SELinux:  Initializing.
[    0.000999] SELinux:  Starting in permissive mode
[    0.001477] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.005168] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.006803] Mount-cache hash table entries: 256
[    0.007305] Initializing cgroup subsys ns
[    0.007425] Initializing cgroup subsys cpuacct
[    0.007539] Initializing cgroup subsys freezer
[    0.007680] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.007810] CPU: L2 cache: 512K
[    0.007916] CPU 0/0x0 -> Node 0
[    0.008012] CPU: Physical Processor ID: 0
[    0.008120] CPU: Processor Core ID: 0
[    0.008228] mce: CPU supports 5 MCE banks
[    0.008343] CPU0: Thermal LVT vector (0xfa) already installed
[    0.008350] using mwait in idle threads.
[    0.008457] Performance Counters: Atom events, Intel PMU driver.
[    0.008613] ... version:                 3
[    0.008719] ... bit width:               40
[    0.008827] ... generic counters:        2
[    0.008934] ... value mask:              000000ffffffffff
[    0.009005] ... max period:              000000007fffffff
[    0.009116] ... fixed-purpose counters:  3
[    0.009223] ... counter mask:            0000000700000003
[    0.009367] ACPI: Core revision 20090521
[    0.023669] Setting APIC routing to flat
[    0.025233] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.035359] CPU0: Intel(R) Atom(TM) CPU D510   @ 1.66GHz stepping 0a
[    0.035994] Booting processor 1 APIC 0x2 ip 0x6000
[    0.000999] Initializing CPU#1
[    0.000999] Calibrating delay using timer specific routine.. 3324.55 BogoMIPS (lpj=1662276)
[    0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.000999] CPU: L2 cache: 512K
[    0.000999] CPU 1/0x2 -> Node 0
[    0.000999] CPU: Physical Processor ID: 0
[    0.000999] CPU: Processor Core ID: 1
[    0.000999] mce: CPU supports 5 MCE banks
[    0.000999] CPU1: Thermal monitoring enabled (TM1)
[    0.000999] x86 PAT enabled: cpu 1, old 0x407050600070106, new 0x7010600070106
[    0.107947] CPU1: Intel(R) Atom(TM) CPU D510   @ 1.66GHz stepping 0a
[    0.108120] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.109161] Booting processor 2 APIC 0x1 ip 0x6000
[    0.000999] Initializing CPU#2
[    0.000999] Calibrating delay using timer specific routine.. 3324.52 BogoMIPS (lpj=1662262)
[    0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.000999] CPU: L2 cache: 512K
[    0.000999] CPU 2/0x1 -> Node 0
[    0.000999] CPU: Physical Processor ID: 0
[    0.000999] CPU: Processor Core ID: 0
[    0.000999] mce: CPU supports 5 MCE banks
[    0.000999] CPU2: Thermal monitoring enabled (TM1)
[    0.000999] x86 PAT enabled: cpu 2, old 0x407050600070106, new 0x7010600070106
[    0.182303] CPU2: Intel(R) Atom(TM) CPU D510   @ 1.66GHz stepping 0a
[    0.184077] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[    0.185189] Booting processor 3 APIC 0x3 ip 0x6000
[    0.000999] Initializing CPU#3
[    0.000999] Calibrating delay using timer specific routine.. 3324.56 BogoMIPS (lpj=1662280)
[    0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.000999] CPU: L2 cache: 512K
[    0.000999] CPU 3/0x3 -> Node 0
[    0.000999] CPU: Physical Processor ID: 0
[    0.000999] CPU: Processor Core ID: 1
[    0.000999] mce: CPU supports 5 MCE banks
[    0.000999] CPU3: Thermal monitoring enabled (TM1)
[    0.000999] x86 PAT enabled: cpu 3, old 0x407050600070106, new 0x7010600070106
[    0.258569] CPU3: Intel(R) Atom(TM) CPU D510   @ 1.66GHz stepping 0a
[    0.259095] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[    0.259987] Brought up 4 CPUs
[    0.260096] Total of 4 processors activated (13299.31 BogoMIPS).
[    0.260354] khelper used greatest stack depth: 5864 bytes left
[    0.262077] xor: automatically using best checksumming function: generic_sse
[    0.266966]    generic_sse:  5056.000 MB/sec
[    0.267076] xor: using function: generic_sse (5056.000 MB/sec)
[    0.267214] Time: 18:33:21  Date: 11/06/23
[    0.267436] NET: Registered protocol family 16
[    0.268990] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[    0.269193] ACPI: bus type pci registered
[    0.269336] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.269336] PCI: Not using MMCONFIG.
[    0.269336] PCI: Using configuration type 1 for base access
[    0.283031] bio: create slab <bio-0> at 0
[    0.286173] ACPI: EC: Look up EC in DSDT
[    0.309422] ACPI: Interpreter enabled
[    0.309542] ACPI: (supports S0 S1 S3 S4 S5)
[    0.309799] ACPI: Using IOAPIC for interrupt routing
[    0.310046] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.322670] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[    0.343211] PCI: Using MMCONFIG at e0000000 - efffffff
[    0.370182] ACPI Warning: Incorrect checksum in table [OEMB] - 4D, should be 4A 20090521 tbutils-246
[    0.371432] ACPI Warning: Incorrect checksum in table [GSCI] - 6A, should be 3E 20090521 tbutils-246
[    0.371960] ACPI: No dock devices found.
[    0.373365] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.373597] pci 0000:00:02.0: reg 10 32bit mmio: [0xfe680000-0xfe6fffff]
[    0.373597] pci 0000:00:02.0: reg 14 io port: [0xa880-0xa887]
[    0.373597] pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xdfffffff]
[    0.373597] pci 0000:00:02.0: reg 1c 32bit mmio: [0xfe700000-0xfe7fffff]
[    0.373597] pci 0000:00:02.1: reg 10 32bit mmio: [0xfea00000-0xfea7ffff]
[    0.373597] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.374010] pci 0000:00:1c.0: PME# disabled
[    0.374188] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[    0.374320] pci 0000:00:1c.4: PME# disabled
[    0.374499] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[    0.374616] pci 0000:00:1c.5: PME# disabled
[    0.374781] pci 0000:00:1d.0: reg 20 io port: [0xac00-0xac1f]
[    0.374860] pci 0000:00:1d.1: reg 20 io port: [0xb000-0xb01f]
[    0.375018] pci 0000:00:1d.2: reg 20 io port: [0xb080-0xb09f]
[    0.375103] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfeafb400-0xfeafb7ff]
[    0.375164] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.375281] pci 0000:00:1d.7: PME# disabled
[    0.375547] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.375562] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.375758] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.375878] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff)
[    0.376079] pci 0000:00:1f.2: reg 10 io port: [0xb400-0xb407]
[    0.376089] pci 0000:00:1f.2: reg 14 io port: [0xbc00-0xbc03]
[    0.376099] pci 0000:00:1f.2: reg 18 io port: [0xb880-0xb887]
[    0.376109] pci 0000:00:1f.2: reg 1c io port: [0xb800-0xb803]
[    0.376119] pci 0000:00:1f.2: reg 20 io port: [0xb480-0xb49f]
[    0.376130] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfeafb800-0xfeafbfff]
[    0.376167] pci 0000:00:1f.2: PME# supported from D3hot
[    0.376284] pci 0000:00:1f.2: PME# disabled
[    0.376467] pci 0000:04:00.0: reg 10 64bit mmio: [0xfeb00000-0xfebfffff]
[    0.376479] pci 0000:04:00.0: reg 18 io port: [0xe800-0xe8ff]
[    0.376587] pci 0000:00:1c.0: bridge io port: [0xe000-0xefff]
[    0.376596] pci 0000:00:1c.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[    0.376606] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xc0000000-0xc01fffff]
[    0.377079] pci 0000:03:00.0: reg 10 64bit mmio: [0xfe9dc000-0xfe9dffff]
[    0.377152] pci 0000:03:00.0: reg 18 io port: [0xd800-0xd8ff]
[    0.377373] pci 0000:03:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9fffff]
[    0.377663] pci 0000:03:00.0: supports D1 D2
[    0.377669] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.377819] pci 0000:03:00.0: PME# disabled
[    0.378117] pci 0000:00:1c.4: bridge io port: [0xd000-0xdfff]
[    0.378125] pci 0000:00:1c.4: bridge 32bit mmio: [0xfe900000-0xfe9fffff]
[    0.378136] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xc0200000-0xc03fffff]
[    0.378550] pci 0000:02:00.0: reg 10 64bit mmio: [0xfe8dc000-0xfe8dffff]
[    0.378626] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff]
[    0.378847] pci 0000:02:00.0: reg 30 32bit mmio: [0xfe8e0000-0xfe8fffff]
[    0.379150] pci 0000:02:00.0: supports D1 D2
[    0.379156] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.379308] pci 0000:02:00.0: PME# disabled
[    0.379595] pci 0000:00:1c.5: bridge io port: [0xc000-0xcfff]
[    0.379603] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
[    0.379613] pci 0000:00:1c.5: bridge 64bit mmio pref: [0xc0400000-0xc05fffff]
[    0.379675] pci 0000:00:1e.0: transparent bridge
[    0.379821] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.380167] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.380575] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.380741] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[    0.380881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[    0.411222] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15), disabled.
[    0.411893] ACPI: PCI Interrupt Link [LNKB] (IRQs *7), disabled.
[    0.412421] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15), disabled.
[    0.413124] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12 14 15), disabled.
[    0.413785] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
[    0.414480] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
[    0.415175] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled.
[    0.415852] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15), disabled.
[    0.417056] SCSI subsystem initialized
[    0.417294] libata version 3.00 loaded.
[    0.435190] raid6: int64x1    324 MB/s
[    0.452017] raid6: int64x2    500 MB/s
[    0.469020] raid6: int64x4    625 MB/s
[    0.486058] raid6: int64x8    667 MB/s
[    0.503076] raid6: sse2x1     613 MB/s
[    0.520012] raid6: sse2x2    1117 MB/s
[    0.537030] raid6: sse2x4    1972 MB/s
[    0.537138] raid6: using algorithm sse2x4 (1972 MB/s)
[    0.537325] PCI: Using ACPI for IRQ routing
[    0.556079] cfg80211: Using static regulatory domain info
[    0.556130] cfg80211: Regulatory domain: US
[    0.556240] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    0.556433] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[    0.556551] 	(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.556668] 	(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.556786] 	(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.557007] 	(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[    0.557125] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[    0.557255] cfg80211: Calling CRDA for country: US
[    0.557394] NetLabel: Initializing
[    0.557394] NetLabel:  domain hash size = 128
[    0.557394] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.557394] NetLabel:  unlabeled traffic allowed by default
[    0.558231] hpet clockevent registered
[    0.558240] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[    0.558363] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[    0.558569] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[    0.571024] pnp: PnP ACPI init
[    0.571171] ACPI: bus type pnp registered
[    0.583423] pnp: PnP ACPI: found 14 devices
[    0.583541] ACPI: ACPI bus type pnp unregistered
[    0.583677] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[    0.583798] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
[    0.583932] system 00:08: ioport range 0xa00-0xa0f has been reserved
[    0.584062] system 00:08: ioport range 0xa10-0xa1f has been reserved
[    0.584180] system 00:08: ioport range 0xa20-0xa2f has been reserved
[    0.584300] system 00:08: ioport range 0xa30-0xa3f has been reserved
[    0.584430] system 00:09: ioport range 0x4d0-0x4d1 has been reserved
[    0.584548] system 00:09: ioport range 0x800-0x87f has been reserved
[    0.584666] system 00:09: ioport range 0x480-0x4ff could not be reserved
[    0.584786] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.584907] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved
[    0.585037] system 00:09: iomem range 0xfed40000-0xfed8ffff has been reserved
[    0.585168] system 00:0b: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.585366] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.585495] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
[    0.585624] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[    0.585742] system 00:0d: iomem range 0xc0000-0xcffff has been reserved
[    0.585860] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[    0.585980] system 00:0d: iomem range 0x100000-0xbf6fffff could not be reserved
[    0.586185] system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved
[    0.592509] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04
[    0.592631] pci 0000:00:1c.0:   IO window: 0xe000-0xefff
[    0.592746] pci 0000:00:1c.0:   MEM window: 0xfeb00000-0xfebfffff
[    0.592864] pci 0000:00:1c.0:   PREFETCH window: 0x000000c0000000-0x000000c01fffff
[    0.593071] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[    0.593187] pci 0000:00:1c.4:   IO window: 0xd000-0xdfff
[    0.593304] pci 0000:00:1c.4:   MEM window: 0xfe900000-0xfe9fffff
[    0.593422] pci 0000:00:1c.4:   PREFETCH window: 0x000000c0200000-0x000000c03fffff
[    0.593619] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02
[    0.593734] pci 0000:00:1c.5:   IO window: 0xc000-0xcfff
[    0.593849] pci 0000:00:1c.5:   MEM window: 0xfe800000-0xfe8fffff
[    0.593965] pci 0000:00:1c.5:   PREFETCH window: 0x000000c0400000-0x000000c05fffff
[    0.594171] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.596374] pci 0000:00:1e.0:   IO window: disabled
[    0.596488] pci 0000:00:1e.0:   MEM window: disabled
[    0.596600] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.596730]   alloc irq_desc for 17 on node 0
[    0.596735]   alloc kstat_irqs on node 0
[    0.596750] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.596872] pci 0000:00:1c.0: setting latency timer to 64
[    0.596886] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.597016] pci 0000:00:1c.4: setting latency timer to 64
[    0.597029]   alloc irq_desc for 16 on node 0
[    0.597033]   alloc kstat_irqs on node 0
[    0.597043] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.597165] pci 0000:00:1c.5: setting latency timer to 64
[    0.597176] pci 0000:00:1e.0: setting latency timer to 64
[    0.597185] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
[    0.597192] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[    0.597199] pci_bus 0000:04: resource 0 io:  [0xe000-0xefff]
[    0.597206] pci_bus 0000:04: resource 1 mem: [0xfeb00000-0xfebfffff]
[    0.597213] pci_bus 0000:04: resource 2 pref mem [0xc0000000-0xc01fffff]
[    0.597220] pci_bus 0000:03: resource 0 io:  [0xd000-0xdfff]
[    0.597226] pci_bus 0000:03: resource 1 mem: [0xfe900000-0xfe9fffff]
[    0.597233] pci_bus 0000:03: resource 2 pref mem [0xc0200000-0xc03fffff]
[    0.597240] pci_bus 0000:02: resource 0 io:  [0xc000-0xcfff]
[    0.597246] pci_bus 0000:02: resource 1 mem: [0xfe800000-0xfe8fffff]
[    0.597253] pci_bus 0000:02: resource 2 pref mem [0xc0400000-0xc05fffff]
[    0.597260] pci_bus 0000:01: resource 3 io:  [0x00-0xffff]
[    0.597267] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffffffffffff]
[    0.597357] NET: Registered protocol family 2
[    0.597920] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.601295] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[    0.607815] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.608697] TCP: Hash tables configured (established 524288 bind 65536)
[    0.608825] TCP reno registered
[    0.609244] NET: Registered protocol family 1
[    0.609553] Trying to unpack rootfs image as initramfs...
[    0.610185] rootfs image is not initramfs (no cpio magic); looks like an initrd
[    0.642693] Freeing initrd memory: 17630k freed
[    0.662439] microcode: CPU0 sig=0x106ca, pf=0x8, revision=0x107
[    0.662578] microcode: CPU1 sig=0x106ca, pf=0x8, revision=0x107
[    0.662713] microcode: CPU2 sig=0x106ca, pf=0x8, revision=0x107
[    0.662844] microcode: CPU3 sig=0x106ca, pf=0x8, revision=0x107
[    0.663092] Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[    0.663294] Scanning for low memory corruption every 60 seconds
[    0.664176] audit: initializing netlink socket (disabled)
[    0.664318] type=2000 audit(1699295601.663:1): initialized
[    0.680233] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.688525] VFS: Disk quotas dquot_6.5.2
[    0.688886] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.692626] Installing knfsd (copyright (C) 1996 [email protected]).
[    0.693093] NTFS driver 2.1.29 [Flags: R/W].
[    0.693734] fuse init (API version 7.12)
[    0.694366] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    0.696896] SGI XFS Quota Management subsystem
[    0.697059] msgmni has been set to 7909
[    0.697582] SELinux:  Registering netfilter hooks
[    0.698846] alg: No test for stdrng (krng)
[    0.698979] async_tx: api initialized (sync-only)
[    0.699562] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.699760] io scheduler noop registered
[    0.699867] io scheduler anticipatory registered
[    0.699991] io scheduler deadline registered
[    0.700307] io scheduler cfq registered (default)
[    0.700440] pci 0000:00:02.0: Boot video device
[    0.700931]   alloc irq_desc for 24 on node 0
[    0.700937]   alloc kstat_irqs on node 0
[    0.700971] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X
[    0.700985] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    0.701539]   alloc irq_desc for 25 on node 0
[    0.701544]   alloc kstat_irqs on node 0
[    0.701559] pcieport-driver 0000:00:1c.4: irq 25 for MSI/MSI-X
[    0.701571] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[    0.702113]   alloc irq_desc for 26 on node 0
[    0.702119]   alloc kstat_irqs on node 0
[    0.702132] pcieport-driver 0000:00:1c.5: irq 26 for MSI/MSI-X
[    0.702145] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[    0.702793] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.703186] Initializing ths8200_init
[    0.703414] Initializing dove_adi9889_init
[    0.704301] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.704507] ACPI: Power Button [PWRF]
[    0.704879] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.705103] ACPI: Power Button [PWRB]
[    0.706135] processor LNXCPU:00: registered as cooling_device0
[    0.706825] processor LNXCPU:01: registered as cooling_device1
[    0.707606] processor LNXCPU:02: registered as cooling_device2
[    0.708316] processor LNXCPU:03: registered as cooling_device3
[    0.728242] Non-volatile memory driver v1.3
[    0.728360] Linux agpgart interface v0.103
[    0.728588] agpgart-intel 0000:00:00.0: Intel IGD Chipset
[    0.729069] agpgart-intel 0000:00:00.0: detected 8188K stolen memory
[    0.732747] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[    0.733216] [drm] Initialized drm 1.1.0 20060810
[    0.733460] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.733583] i915 0000:00:02.0: setting latency timer to 64
[    0.764287] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[    0.764494] [drm] MTRR allocation failed.  Graphics performance may suffer.
[    0.764985]   alloc irq_desc for 27 on node 0
[    0.764992]   alloc kstat_irqs on node 0
[    0.765009] i915 0000:00:02.0: irq 27 for MSI/MSI-X
[    0.903594] [drm] Big FIFO is enabled
[    0.965891] [drm] Big FIFO is enabled
[    0.965901] [drm] DAC-6: set mode 1920x1080 17
[    0.965963] [drm] Big FIFO is enabled
[    0.965977] [drm] Big FIFO is enabled
[    1.038408] Console: switching to colour frame buffer device 240x67
[    1.058969] Switched to high resolution mode on CPU 3
[    1.059136] Switched to high resolution mode on CPU 2
[    1.059307] Switched to high resolution mode on CPU 1
[    1.059829] Switched to high resolution mode on CPU 0
[    1.065121] [drm] fb0: inteldrmfb frame buffer device
[    1.065447] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    1.065614] work_for_cpu used greatest stack depth: 3648 bytes left
[    1.065904] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.310123] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.554125] serial8250: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A
[    1.555318] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.555852] 00:07: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A
[    1.562269] brd: module loaded
[    1.565496] loop: module loaded
[    1.566433] ahci 0000:00:1f.2: version 3.0
[    1.566460]   alloc irq_desc for 19 on node 0
[    1.566466]   alloc kstat_irqs on node 0
[    1.566482] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.566679] ** BUFFALO Disable Command Queuing Function [ahci 0000:00:1f.2] **
[    1.566850]   alloc irq_desc for 28 on node 0
[    1.566855]   alloc kstat_irqs on node 0
[    1.566869] ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
[    1.566879] ahci 0000:00:1f.2: controller can't do NCQ, turning off CAP_NCQ
[    1.567097] ahci: SSS flag set, parallel bus scan disabled
[    1.567267] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[    1.567443] ahci 0000:00:1f.2: flags: 64bit sntf stag pm led clo pio slum part ems 
[    1.567606] ahci 0000:00:1f.2: setting latency timer to 64
[    1.577190] scsi0 : ahci
[    1.577806] scsi1 : ahci
[    1.578271] scsi2 : ahci
[    1.578701] scsi3 : ahci
[    1.579137] scsi4 : ahci
[    1.579565] scsi5 : ahci
[    1.580237] ata1: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafb900 irq 28
[    1.580406] ata2: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafb980 irq 28
[    1.580561] ata3: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafba00 irq 28
[    1.580714] ata4: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafba80 irq 28
[    1.580868] ata5: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafbb00 irq 28
[    1.581032] ata6: SATA max UDMA/133 abar m2048@0xfeafb800 port 0xfeafbb80 irq 28
[    1.581728] sata_mv 0000:04:00.0: version 1.28
[    1.581870] ** BUFFALO Disable Command Queuing Function [sata_mv 0000:04:00.0] **
[    1.582070] sata_mv 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.582420] sata_mv 0000:04:00.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[    1.582583] sata_mv 0000:04:00.0: setting latency timer to 64
[    1.583308] scsi6 : sata_mv
[    1.583767] scsi7 : sata_mv
[    1.584186] scsi8 : sata_mv
[    1.584587] scsi9 : sata_mv
[    1.584908] ata7: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb22000 irq 16
[    1.588089] ata8: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb24000 irq 16
[    1.591289] ata9: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb26000 irq 16
[    1.594479] ata10: SATA max UDMA/133 mmio m1048576@0xfeb00000 port 0xfeb28000 irq 16
[    1.598966] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI
[    1.602383] Copyright (c) 1999-2006 Intel Corporation.
[    1.605995] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
[    1.609580] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[    1.613542] sk98lin 0000:03:00.0: enabling device (0000 -> 0003)
[    1.617310] sk98lin 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.621157] sk98lin: Network Device Driver v10.85.9.3
[    1.621160] (C)Copyright 1999-2010 Marvell(R).
[    1.628990] sk98lin 0000:03:00.0: setting latency timer to 64
[    1.630780] eth0: Generic Marvell Yukon chipset Ethernet device
[    1.635087] sk98lin 0000:02:00.0: enabling device (0000 -> 0003)
[    1.639262] sk98lin 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.643544] sk98lin 0000:02:00.0: setting latency timer to 64
[    1.645380] eth1: Generic Marvell Yukon chipset Ethernet device
[    1.650424] PNP: No PS/2 controller found. Probing ports directly.
[    1.655437] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.659953] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.664730] mice: PS/2 mouse device common for all mice
[    1.670754] rtc_cmos 00:03: RTC can wake from S4
[    1.675653] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.680474] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[    1.685605] md: raid0 personality registered for level 0
[    1.690592] md: raid1 personality registered for level 1
[    1.695512] md: raid6 personality registered for level 6
[    1.700438] md: raid5 personality registered for level 5
[    1.705329] md: raid4 personality registered for level 4
[    1.710953] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: [email protected]
[    1.716777] cpuidle: using governor ladder
[    1.721781] cpuidle: using governor menu
[    1.726954] Kernel event proc (C) BUFFALO INC. V.1.00 installed.
[    1.731904] MICON ctrl (C) BUFFALO INC. V.1.00 installed.
[    1.736812] UPSDRV (C) BUFFALO INC. V.1.00 installed.
[    1.741705]   OMRON contact type ups shutdown support enabled!
[    1.746609] [hdd control module init proc]
[    1.751562] buffalo/gpio directory create successful.....
[    1.756520] hotplug directory create successful.....
[    1.761536] HDD0_PRESENT_STATUS_FILE create successful.....
[    1.766582] HDD1_PRESENT_STATUS_FILE create successful.....
[    1.771583] HDD2_PRESENT_STATUS_FILE create successful.....
[    1.776490] HDD3_PRESENT_STATUS_FILE create successful.....
[    1.781294] HDD4_PRESENT_STATUS_FILE create successful.....
[    1.786008] HDD5_PRESENT_STATUS_FILE create successful.....
[    1.790631] HDD6_PRESENT_STATUS_FILE create successful.....
[    1.795145] HDD7_PRESENT_STATUS_FILE create successful.....
[    1.799576] power_control directory create successful.....
[    1.803968] HDD0_POWER_STATUS_FILE create successful.....
[    1.808428] HDD1_POWER_STATUS_FILE create successful.....
[    1.812887] HDD2_POWER_STATUS_FILE create successful.....
[    1.817352] HDD3_POWER_STATUS_FILE create successful.....
[    1.821813] HDD4_POWER_STATUS_FILE create successful.....
[    1.826280] HDD5_POWER_STATUS_FILE create successful.....
[    1.830646] HDD6_POWER_STATUS_FILE create successful.....
[    1.835011] HDD7_POWER_STATUS_FILE create successful.....
[    1.839370] hdd control module 0.2 initialized...
[    1.843818] buffalo/gpio/switch directory create successful.....
[    1.848339] buffalo/gpio/switch/func create successful.....
[    1.852900] buffalo/gpio/switch/display create successful.....
[    1.857405] enter fan module init
[    1.862143] enter cmos module init
[    1.866752] Netfilter messages via NETLINK v0.30.
[    1.872020] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.876384] TCP cubic registered
[    1.880750] NET: Registered protocol family 17
[    1.885455] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    1.886108] RPC: Registered udp transport module.
[    1.886114] RPC: Registered tcp transport module.
[    1.886800] PM: Resume from disk failed.
[    1.886835] registered taskstats version 1
[    1.887109]   Magic number: 15:420:594
[    2.052451] ata1.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100
[    2.056942] ata1.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.062123] ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.063066] ata1.00: configured for UDMA/100
[    2.074366] scsi 0:0:0:0: Direct-Access     ATA      MG04ACA600E      FS3J PQ: 0 ANSI: 5
[    2.079789] sd 0:0:0:0: [sda] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    2.079968] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.088975] sd 0:0:0:0: [sda] 4096-byte physical blocks
[    2.093670] sd 0:0:0:0: [sda] Write Protect is off
[    2.098195] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.098288] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.103312]  sda: sda1 sda9
[    2.366780] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.409078] ata7.00: ATA-8: TOSHIBA MG04ACA600E, FS3B, max UDMA/100
[    2.413636] ata7.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.427105] ata7.00: configured for UDMA/100
[    2.813030] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.834479] ata2.00: ATA-8: TOSHIBA MG04ACA600E, FS4B, max UDMA/100
[    2.839202] ata2.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.845527] ata2.00: configured for UDMA/100
[    2.861219] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA MG04ACA6 FS4B PQ: 0 ANSI: 5
[    2.866766] sd 1:0:0:0: [sdb] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    2.867801] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    2.876626] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.881721] sd 1:0:0:0: [sdb] Write Protect is off
[    2.886672] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.886753] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.892218]  sdb: sdb1 sdb9
[    2.953795] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.590032] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    3.737478] ata3.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100
[    3.742515] ata3.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    3.749148] ata3.00: configured for UDMA/100
[    3.765227] scsi 2:0:0:0: Direct-Access     ATA      MG04ACA600E      FS3J PQ: 0 ANSI: 5
[    3.770989] sd 2:0:0:0: [sdc] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    3.771286] sd 2:0:0:0: Attached scsi generic sg2 type 0
[    3.781299] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[    3.786530] sd 2:0:0:0: [sdc] Write Protect is off
[    3.791649] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    3.791732] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.797422]  sdc: sdc1 sdc9
[    4.058762] sd 2:0:0:0: [sdc] Attached SCSI disk
[    4.494031] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    4.644001] ata4.00: ATA-8: TOSHIBA MG04ACA600E, FS4B, max UDMA/100
[    4.649549] ata4.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    4.656804] ata4.00: configured for UDMA/100
[    4.673234] scsi 3:0:0:0: Direct-Access     ATA      TOSHIBA MG04ACA6 FS4B PQ: 0 ANSI: 5
[    4.679668] sd 3:0:0:0: [sdd] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    4.679926] sd 3:0:0:0: Attached scsi generic sg3 type 0
[    4.691353] sd 3:0:0:0: [sdd] 4096-byte physical blocks
[    4.697403] sd 3:0:0:0: [sdd] Write Protect is off
[    4.703358] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[    4.703438] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.709954]  sdd: sdd1 sdd9
[    4.985031] ata5: SATA link down (SStatus 0 SControl 300)
[    4.996521] sd 3:0:0:0: [sdd] Attached SCSI disk
[    5.305026] ata6: SATA link down (SStatus 0 SControl 300)
[    5.322231] scsi 6:0:0:0: Direct-Access     ATA      TOSHIBA MG04ACA6 FS3B PQ: 0 ANSI: 5
[    5.329310] sd 6:0:0:0: [sde] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    5.329574] sd 6:0:0:0: Attached scsi generic sg4 type 0
[    5.342274] sd 6:0:0:0: [sde] 4096-byte physical blocks
[    5.348831] sd 6:0:0:0: [sde] Write Protect is off
[    5.355233] sd 6:0:0:0: [sde] Mode Sense: 00 3a 00 00
[    5.355316] sd 6:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    5.362228]  sde: sde1 sde9
[    5.629998] sd 6:0:0:0: [sde] Attached SCSI disk
[    5.787063] ata8: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    5.948070] ata8.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100
[    5.954526] ata8.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    5.970100] ata8.00: configured for UDMA/100
[    5.976850] scsi 7:0:0:0: Direct-Access     ATA      MG04ACA600E      FS3J PQ: 0 ANSI: 5
[    5.984298] sd 7:0:0:0: [sdf] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    5.984587] sd 7:0:0:0: Attached scsi generic sg5 type 0
[    5.997720] sd 7:0:0:0: [sdf] 4096-byte physical blocks
[    6.004498] sd 7:0:0:0: [sdf] Write Protect is off
[    6.011073] sd 7:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[    6.011153] sd 7:0:0:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.018193]  sdf: sdf1 sdf9
[    6.278905] sd 7:0:0:0: [sdf] Attached SCSI disk
[    6.443050] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    6.585068] ata9.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100
[    6.591719] ata9.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    6.607101] ata9.00: configured for UDMA/100
[    6.613876] scsi 8:0:0:0: Direct-Access     ATA      MG04ACA600E      FS3J PQ: 0 ANSI: 5
[    6.621226] sd 8:0:0:0: [sdg] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    6.621543] sd 8:0:0:0: Attached scsi generic sg6 type 0
[    6.634721] sd 8:0:0:0: [sdg] 4096-byte physical blocks
[    6.641515] sd 8:0:0:0: [sdg] Write Protect is off
[    6.648105] sd 8:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[    6.648184] sd 8:0:0:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.655297]  sdg: sdg1 sdg9
[    6.914987] sd 8:0:0:0: [sdg] Attached SCSI disk
[    7.081049] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    7.242066] ata10.00: ATA-8: MG04ACA600E, FS3J, max UDMA/100
[    7.248654] ata10.00: 11721045168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    7.264101] ata10.00: configured for UDMA/100
[    7.270881] scsi 9:0:0:0: Direct-Access     ATA      MG04ACA600E      FS3J PQ: 0 ANSI: 5
[    7.278262] sd 9:0:0:0: [sdh] 11721045168 512-byte logical blocks: (6.00 TB/5.45 TiB)
[    7.285038] sd 9:0:0:0: [sdh] 4096-byte physical blocks
[    7.285746] sd 9:0:0:0: Attached scsi generic sg7 type 0
[    7.298524] sd 9:0:0:0: [sdh] Write Protect is off
[    7.305102] sd 9:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[    7.305193] sd 9:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    7.312298]  sdh: sdh1 sdh9
[    7.570863] sd 9:0:0:0: [sdh] Attached SCSI disk
[    7.577532] md: Waiting for all devices to be available before autodetect
[    7.584192] md: If you don't use raid, use raid=noautodetect
[    7.591304] md: Autodetecting RAID arrays.
[    7.597843] md: Scanned 0 and added 0 devices.
[    7.604368] md: autorun ...
[    7.610873] md: ... autorun DONE.
[    7.617396] RAMDISK: gzip image found at block 0
[    8.925136] VFS: Mounted root (ext2 filesystem) on device 1:0.
[    9.040492] bootver=BOOTVER=Unkown
[    9.046936] buffalo_series_name=TeraStation
[    9.053299] buffalo_product_name=TS-QVHL/R5(SAIMEI)
[   11.391793] usbcore: registered new interface driver usbfs
[   11.397784] usbcore: registered new interface driver hub
[   11.403595] usbcore: registered new device driver usb
[   11.423642] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   11.429332]   alloc irq_desc for 23 on node 0
[   11.429339]   alloc kstat_irqs on node 0
[   11.429355] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   11.434977] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[   11.434985] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   11.440584] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[   11.450031] ehci_hcd 0000:00:1d.7: debug port 1
[   11.455499] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[   11.455536] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfeafb400
[   11.470023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[   11.475448] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   11.480820] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.486164] usb usb1: Product: EHCI Host Controller
[   11.491508] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd
[   11.496905] usb usb1: SerialNumber: 0000:00:1d.7
[   11.502491] usb usb1: configuration #1 chosen from 1 choice
[   11.507948] hub 1-0:1.0: USB hub found
[   11.513261] hub 1-0:1.0: 6 ports detected
[   11.526327] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   11.539085] uhci_hcd: USB Universal Host Controller Interface driver
[   11.544749] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[   11.550071] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[   11.550079] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   11.555333] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[   11.560599] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ac00
[   11.565858] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[   11.571102] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.576361] usb usb2: Product: UHCI Host Controller
[   11.581571] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[   11.586743] usb usb2: SerialNumber: 0000:00:1d.0
[   11.592161] usb usb2: configuration #1 chosen from 1 choice
[   11.597476] hub 2-0:1.0: USB hub found
[   11.602586] hub 2-0:1.0: 2 ports detected
[   11.608000] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[   11.613188] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[   11.613196] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   11.618401] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[   11.623665] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000
[   11.628942] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[   11.634155] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.639358] usb usb3: Product: UHCI Host Controller
[   11.644569] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[   11.649798] usb usb3: SerialNumber: 0000:00:1d.1
[   11.655209] usb usb3: configuration #1 chosen from 1 choice
[   11.660575] hub 3-0:1.0: USB hub found
[   11.665770] hub 3-0:1.0: 2 ports detected
[   11.671281]   alloc irq_desc for 18 on node 0
[   11.671287]   alloc kstat_irqs on node 0
[   11.671303] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[   11.676552] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[   11.676559] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   11.681735] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[   11.686915] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b080
[   11.692182] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[   11.697475] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   11.702852] usb usb4: Product: UHCI Host Controller
[   11.708299] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[   11.713827] usb usb4: SerialNumber: 0000:00:1d.2
[   11.719710] usb usb4: configuration #1 chosen from 1 choice
[   11.725531] hub 4-0:1.0: USB hub found
[   11.731171] hub 4-0:1.0: 2 ports detected
[   11.743104] usbcore: registered new interface driver libusual
[   11.759730] Initializing USB Mass Storage driver...
[   11.765622] usbcore: registered new interface driver usb-storage
[   11.771354] USB Mass Storage support registered.
[   11.784400] usbcore: registered new interface driver usblp
[   11.802255] usbcore: registered new interface driver hiddev
[   11.808042] usbcore: registered new interface driver usbhid
[   11.813606] usbhid: v2.6:USB HID core driver
[   11.872039] usb 1-2: new high speed USB device using ehci_hcd and address 3
[   11.992053] usb 1-2: New USB device found, idVendor=346d, idProduct=5678
[   11.997632] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   12.003181] usb 1-2: Product: Disk 20
[   12.008739] usb 1-2: Manufacturer: USB
[   12.014284] usb 1-2: SerialNumber: FC16684F50E61
[   12.020144] usb 1-2: configuration #1 chosen from 1 choice
[   12.026394] scsi10 : SCSI emulation for USB Mass Storage devices
[   12.032392] usb-storage: device found at 3
[   12.032399] usb-storage: waiting for device to settle before scanning
[   12.238029] usb 2-1: new low speed USB device using uhci_hcd and address 2
[   12.413672] usb 2-1: New USB device found, idVendor=0518, idProduct=0001
[   12.419311] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   12.424919] usb 2-1: Product: USB-compliant keyboard
[   12.430531] usb 2-1: Manufacturer: Plus More Enterprise LTD.
[   12.436436] usb 2-1: configuration #1 chosen from 1 choice
[   12.460412] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input2
[   12.466677] generic-usb 0003:0518:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0
[   12.489485] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input3
[   12.496212] generic-usb 0003:0518:0001.0002: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1
[   17.032706] scsi 10:0:0:0: Direct-Access     VendorC  ProductCode      2.00 PQ: 0 ANSI: 4
[   17.040392] sd 10:0:0:0: Attached scsi generic sg8 type 0
[   17.047200] sd 10:0:0:0: [sdi] 61440000 512-byte logical blocks: (31.4 GB/29.2 GiB)
[   17.048155] usb-storage: device scan complete
[   17.054539] sd 10:0:0:0: [sdi] Write Protect is off
[   17.061198] sd 10:0:0:0: [sdi] Mode Sense: 03 00 00 00
[   17.061205] sd 10:0:0:0: [sdi] Assuming drive cache: write through
[   17.070154] sd 10:0:0:0: [sdi] Assuming drive cache: write through
[   17.076756]  sdi: sdi1
[   17.085781] sd 10:0:0:0: [sdi] Assuming drive cache: write through
[   17.092380] sd 10:0:0:0: [sdi] Attached SCSI removable disk
[   18.111401] usbcore: deregistering interface driver usbhid
[   18.155992] usbcore: deregistering interface driver hiddev
[   18.171143] usbcore: deregistering interface driver usblp
[   18.184404] usbcore: deregistering interface driver usb-storage
[   18.197397] usbcore: deregistering interface driver libusual
[   18.212060] uhci_hcd 0000:00:1d.2: remove, state 4
[   18.218253] usb usb4: USB disconnect, address 1
[   18.225079] uhci_hcd 0000:00:1d.2: USB bus 4 deregistered
[   18.231270] uhci_hcd 0000:00:1d.2: PCI INT C disabled
[   18.237386] uhci_hcd 0000:00:1d.1: remove, state 4
[   18.243467] usb usb3: USB disconnect, address 1
[   18.250158] uhci_hcd 0000:00:1d.1: USB bus 3 deregistered
[   18.256306] uhci_hcd 0000:00:1d.1: PCI INT B disabled
[   18.262363] uhci_hcd 0000:00:1d.0: remove, state 1
[   18.268378] usb usb2: USB disconnect, address 1
[   18.274358] usb 2-1: USB disconnect, address 2
[   18.281720] uhci_hcd 0000:00:1d.0: USB bus 2 deregistered
[   18.287721] uhci_hcd 0000:00:1d.0: PCI INT A disabled
[   18.309431] ehci_hcd 0000:00:1d.7: remove, state 1
[   18.315315] usb usb1: USB disconnect, address 1
[   18.321145] usb 1-2: USB disconnect, address 3
[   18.332186] ehci_hcd 0000:00:1d.7: USB bus 1 deregistered
[   18.338111] ehci_hcd 0000:00:1d.7: PCI INT A disabled
[   18.354405] usbcore: deregistering device driver usb
[   18.360431] usbcore: deregistering interface driver usbfs
[   18.366512] usbcore: deregistering interface driver hub
[   18.543168] md: md0 stopped.
[   18.558210] md: md1 stopped.
[   18.572272] md: md2 stopped.
[   18.602824] Freeing unused kernel memory: 548k freed
[   18.608710] Write protecting the kernel read-only data: 7448k
[  102.256900] AC Power Loss is 2
[  107.883671]   alloc irq_desc for 29 on node 0
[  107.883679]   alloc kstat_irqs on node 0
[  107.883703] sk98lin 0000:03:00.0: irq 29 for MSI/MSI-X
[  110.601306] eth1: network connection up using port A
[  110.601306]     interrupt src:   MSI
[  110.601306]     speed:           1000
[  110.601306]     autonegotiation: yes
[  110.601306]     duplex mode:     full
[  110.601306]     flowctrl:        symmetric
[  110.601306]     role:            slave
[  110.601306]     tcp offload:     enabled
[  110.601306]     scatter-gather:  enabled
[  110.601306]     tx-checksum:     enabled
[  110.601306]     rx-checksum:     enabled
[  110.601306]     rx-polling:      enabled
[  111.906444]   alloc irq_desc for 30 on node 0
[  111.906452]   alloc kstat_irqs on node 0
[  111.906476] sk98lin 0000:02:00.0: irq 30 for MSI/MSI-X
[  148.827790] usbcore: registered new interface driver usbfs
[  148.833115] usbcore: registered new interface driver hub
[  148.844425] usbcore: registered new device driver usb
[  148.868503] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[  148.879326] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[  148.884629] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[  148.884643] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[  148.890000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[  148.899300] ehci_hcd 0000:00:1d.7: debug port 1
[  148.904537] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[  148.904580] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfeafb400
[  148.920050] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[  148.925437] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[  148.930854] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  148.935566] usb usb1: Product: EHCI Host Controller
[  148.940890] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd
[  148.945288] usb usb1: SerialNumber: 0000:00:1d.7
[  148.956543] usb usb1: configuration #1 chosen from 1 choice
[  148.958499] hub 1-0:1.0: USB hub found
[  148.958528] hub 1-0:1.0: 6 ports detected
[  148.988655] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[  149.006477] uhci_hcd: USB Universal Host Controller Interface driver
[  149.016076] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[  149.022203] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[  149.022216] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[  149.028773] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[  149.034266] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000ac00
[  149.039472] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[  149.045152] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  149.050723] usb usb2: Product: UHCI Host Controller
[  149.056292] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[  149.062223] usb usb2: SerialNumber: 0000:00:1d.0
[  149.071683] usb usb2: configuration #1 chosen from 1 choice
[  149.081702] hub 2-0:1.0: USB hub found
[  149.086566] hub 2-0:1.0: 2 ports detected
[  149.096302] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[  149.101416] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[  149.101424] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[  149.106946] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[  149.112531] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000
[  149.118377] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[  149.124235] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  149.129814] usb usb3: Product: UHCI Host Controller
[  149.135417] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[  149.142226] usb usb3: SerialNumber: 0000:00:1d.1
[  149.148877] usb usb3: configuration #1 chosen from 1 choice
[  149.155691] hub 3-0:1.0: USB hub found
[  149.161187] hub 3-0:1.0: 2 ports detected
[  149.167188] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[  149.172781] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[  149.172791] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[  149.178314] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[  149.183758] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b080
[  149.189284] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[  149.194684] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[  149.200127] usb usb4: Product: UHCI Host Controller
[  149.205542] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd
[  149.211000] usb usb4: SerialNumber: 0000:00:1d.2
[  149.216755] usb usb4: configuration #1 chosen from 1 choice
[  149.222394] hub 4-0:1.0: USB hub found
[  149.227803] hub 4-0:1.0: 2 ports detected
[  149.239651] usbcore: registered new interface driver libusual
[  149.256810] Initializing USB Mass Storage driver...
[  149.262584] usbcore: registered new interface driver usb-storage
[  149.268261] USB Mass Storage support registered.
[  149.284149] usbcore: registered new interface driver usblp
[  149.302034] usbcore: registered new interface driver hiddev
[  149.308256] usbcore: registered new interface driver usbhid
[  149.314124] usbhid: v2.6:USB HID core driver
[  149.325312] usb 1-2: new high speed USB device using ehci_hcd and address 3
[  149.447042] usb 1-2: New USB device found, idVendor=346d, idProduct=5678
[  149.452752] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  149.459239] usb 1-2: Product: Disk 20
[  149.465213] usb 1-2: Manufacturer: USB
[  149.465221] usb 1-2: SerialNumber: FC16684F50E61
[  149.465661] usb 1-2: configuration #1 chosen from 1 choice
[  149.466369] scsi11 : SCSI emulation for USB Mass Storage devices
[  149.466838] usb-storage: device found at 3
[  149.466845] usb-storage: waiting for device to settle before scanning
[  149.569084] usb 2-1: new low speed USB device using uhci_hcd and address 2
[  149.747319] usb 2-1: New USB device found, idVendor=0518, idProduct=0001
[  149.754561] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  149.761784] usb 2-1: Product: USB-compliant keyboard
[  149.768261] usb 2-1: Manufacturer: Plus More Enterprise LTD.
[  149.774247] usb 2-1: configuration #1 chosen from 1 choice
[  149.798056] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.0/input/input4
[  149.805236] generic-usb 0003:0518:0001.0003: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0
[  149.828136] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1:1.1/input/input5
[  149.828714] generic-usb 0003:0518:0001.0004: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1
[  150.188391] set AC Power Loss to 0
[  154.466703] scsi 11:0:0:0: Direct-Access     VendorC  ProductCode      2.00 PQ: 0 ANSI: 4
[  154.476423] sd 11:0:0:0: Attached scsi generic sg8 type 0
[  154.483718] sd 11:0:0:0: [sdi] 61440000 512-byte logical blocks: (31.4 GB/29.2 GiB)
[  154.492791] sd 11:0:0:0: [sdi] Write Protect is off
[  154.501273] sd 11:0:0:0: [sdi] Mode Sense: 03 00 00 00
[  154.501284] sd 11:0:0:0: [sdi] Assuming drive cache: write through
[  154.503593] usb-storage: device scan complete
[  154.510517] sd 11:0:0:0: [sdi] Assuming drive cache: write through
[  154.517080]  sdi: sdi1
[  154.526427] sd 11:0:0:0: [sdi] Assuming drive cache: write through
[  154.533209] sd 11:0:0:0: [sdi] Attached SCSI removable disk


Buffalo Resources