Terastation TS-6VHL
Specs
| CPU | Intel Atom D510 1.66GHz Dual-Core (64-bit) |
| Memory | 2 GB DDR2 (Upgradable to 4GB) |
| Bays | 6 |
| Network | 2x 10/100/1000 Mbps (Marvell 88e8059) |
| Sata | 6x SATA II (Intel 82801ir) |
| USB 2.0 | 2x Back |
| USB 3.0 | 2x Back (D720200) |
| Serial port | 1x Back |
| VGA | Yes |
| Fan | 2x |
| Power | Internal AC 100-240V, universal 50/60Hz |
Stock Firmware Installation
You can re-install the linux-based firmware by creating a recovery disk, see Create Recovery Disk for Intel-based Terastation You can then boot from it by switching the boot mode switch on the back to "USB", after a few minutes the device will go into EM Mode Then you can install the firmware using the firmware updater in debug mode, see Enable Debug mode for LSUpdater/TSUpdater
Custom Firmware/Operating System installation
These devices run on an Intel Atom processor with a fairly typical BIOS and include a VGA out and support USB keyboards, you should be able to run virtually any operating system that will run on a normal PC depending on drivers/etc.
For tools to help install and configure Debian on these devices, see Installing Debian on Intel Terastations
Pictures
DMESG output
[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.31.8-atom_d510 (root@HP7907) (gcc version 4.2.0 20070413 (prerelease)) #1 SMP Tue Dec 19 14:06:42 JST 2017 [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-atom_d510.buffalo root=md1 rw console=tty0 SERIES=TeraStation PRODUCTNAME=TS-QVHL(SAIMEI) PRODUCTID=0x00002013 SERIES=TeraStation PRODUCTNAME=TS-QVHL(SAIMEI) PRODUCTID=0x00002013 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable) [ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bf580000 (usable) [ 0.000000] BIOS-e820: 00000000bf580000 - 00000000bf58e000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bf5d0000 - 00000000bf5e0000 (reserved) [ 0.000000] BIOS-e820: 00000000bf5e7000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] DMI present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] last_pfn = 0x140000 max_arch_pfn = 0x400000000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] last_pfn = 0xbf580 max_arch_pfn = 0x400000000 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable) [ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000e4000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 00000000bf580000 (usable) [ 0.000000] modified: 00000000bf580000 - 00000000bf58e000 (ACPI data) [ 0.000000] modified: 00000000bf58e000 - 00000000bf5d0000 (ACPI NVS) [ 0.000000] modified: 00000000bf5d0000 - 00000000bf5e0000 (reserved) [ 0.000000] modified: 00000000bf5e7000 - 00000000c0000000 (reserved) [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] modified: 00000000ffe00000 - 0000000100000000 (reserved) [ 0.000000] modified: 0000000100000000 - 0000000140000000 (usable) [ 0.000000] init_memory_mapping: 0000000000000000-00000000bf580000 [ 0.000000] init_memory_mapping: 0000000100000000-0000000140000000 [ 0.000000] RAMDISK: 36eb7000 - 37fefb18 [ 0.000000] ACPI: RSDP 00000000000f9f30 00024 (v02 ACPIAM) [ 0.000000] ACPI: XSDT 00000000bf580100 00054 (v01 MATSU SLIC1108 20101228 MSFT 00000097) [ 0.000000] ACPI: FACP 00000000bf580290 000F4 (v04 122810 FACP0918 20101228 MSFT 00000097) [ 0.000000] ACPI: DSDT 00000000bf5805c0 05CE6 (v02 WSQVL WSQVL301 00000301 INTL 20051117) [ 0.000000] ACPI: FACS 00000000bf58e000 00040 [ 0.000000] ACPI: APIC 00000000bf580390 0006C (v02 122810 APIC0918 20101228 MSFT 00000097) [ 0.000000] ACPI: MCFG 00000000bf580400 0003C (v01 122810 OEMMCFG 20101228 MSFT 00000097) [ 0.000000] ACPI: SLIC 00000000bf580440 00176 (v01 MATSU SLIC1108 20101228 MSFT 00000097) [ 0.000000] ACPI: OEMB 00000000bf58e040 00082 (v01 122810 OEMB0918 20101228 MSFT 00000097) [ 0.000000] ACPI: GSCI 00000000bf58e0d0 02024 (v01 122810 GMCHSCI 20101228 MSFT 00000097) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-0000000140000000 [ 0.000000] Bootmem setup node 0 0000000000000000-0000000140000000 [ 0.000000] NODE_DATA [0000000000014000 - 0000000000018fff] [ 0.000000] bootmap [0000000000019000 - 0000000000040fff] pages 28 [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0140000000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] [ 0.000000] #2 [0001000000 - 0001933734] TEXT DATA BSS ==> [0001000000 - 0001933734] [ 0.000000] #3 [0036eb7000 - 0037fefb18] RAMDISK ==> [0036eb7000 - 0037fefb18] [ 0.000000] #4 [000009e800 - 0000100000] BIOS reserved ==> [000009e800 - 0000100000] [ 0.000000] #5 [0001934000 - 000193420f] BRK ==> [0001934000 - 000193420f] [ 0.000000] #6 [0000010000 - 0000013000] PGTABLE ==> [0000010000 - 0000013000] [ 0.000000] #7 [0000013000 - 0000014000] PGTABLE ==> [0000013000 - 0000014000] [ 0.000000] found SMP MP-table at [ffff8800000ff780] ff780 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] DMA32 0x00001000 -> 0x00100000 [ 0.000000] Normal 0x00100000 -> 0x00140000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009e [ 0.000000] 0: 0x00000100 -> 0x000bf580 [ 0.000000] 0: 0x00100000 -> 0x00140000 [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 4, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000 [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000 [ 0.000000] PM: Registered nosave memory: 00000000bf580000 - 00000000bf58e000 [ 0.000000] PM: Registered nosave memory: 00000000bf58e000 - 00000000bf5d0000 [ 0.000000] PM: Registered nosave memory: 00000000bf5d0000 - 00000000bf5e0000 [ 0.000000] PM: Registered nosave memory: 00000000bf5e0000 - 00000000bf5e7000 [ 0.000000] PM: Registered nosave memory: 00000000bf5e7000 - 00000000c0000000 [ 0.000000] PM: Registered nosave memory: 00000000c0000000 - 00000000fee00000 [ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000 [ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffe00000 [ 0.000000] PM: Registered nosave memory: 00000000ffe00000 - 0000000100000000 [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:3ee00000) [ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 28 pages at ffff880028022000, static data 82848 bytes [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1027750 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-atom_d510.buffalo root=md1 rw console=tty0 SERIES=TeraStation PRODUCTNAME=TS-QVHL(SAIMEI) PRODUCTID=0x00002013 SERIES=TeraStation PRODUCTNAME=TS-QVHL(SAIMEI) PRODUCTID=0x00002013 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] Initializing CPU#0 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.000000] Placing 64MB software IO TLB between ffff880020000000 - ffff880024000000 [ 0.000000] software IO TLB at phys 0x20000000 - 0x24000000 [ 0.000000] Memory: 4032052k/5242880k available (5097k kernel code, 1059784k absent, 151044k reserved, 2891k data, 548k init) [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:440 [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 1662.558 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.11 BogoMIPS (lpj=1662558) [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Initializing. [ 0.001534] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.005124] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.006705] Mount-cache hash table entries: 256 [ 0.007225] Initializing cgroup subsys ns [ 0.007365] Initializing cgroup subsys cpuacct [ 0.007498] Initializing cgroup subsys freezer [ 0.007655] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.007818] CPU: L2 cache: 512K [ 0.007942] CPU 0/0x0 -> Node 0 [ 0.008010] CPU: Physical Processor ID: 0 [ 0.008135] CPU: Processor Core ID: 0 [ 0.008261] mce: CPU supports 5 MCE banks [ 0.008395] CPU0: Thermal monitoring enabled (TM1) [ 0.008524] using mwait in idle threads. [ 0.008645] Performance Counters: Atom events, Intel PMU driver. [ 0.008844] ... version: 3 [ 0.009005] ... bit width: 40 [ 0.009127] ... generic counters: 2 [ 0.009249] ... value mask: 000000ffffffffff [ 0.009375] ... max period: 000000007fffffff [ 0.009502] ... fixed-purpose counters: 3 [ 0.009624] ... counter mask: 0000000700000003 [ 0.009784] ACPI: Core revision 20090521 [ 0.025113] Setting APIC routing to flat [ 0.025578] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.035715] CPU0: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.035994] Booting processor 1 APIC 0x2 ip 0x6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 3324.54 BogoMIPS (lpj=1662270) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 1/0x2 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU1: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 0.108901] CPU1: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.109151] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.110208] Booting processor 2 APIC 0x1 ip 0x6000 [ 0.000999] Initializing CPU#2 [ 0.000999] Calibrating delay using timer specific routine.. 3324.54 BogoMIPS (lpj=1662271) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 2/0x1 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 0 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU2: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 2, old 0x7040600070406, new 0x7010600070106 [ 0.183242] CPU2: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.185142] checking TSC synchronization [CPU#0 -> CPU#2]: passed. [ 0.186180] Booting processor 3 APIC 0x3 ip 0x6000 [ 0.000999] Initializing CPU#3 [ 0.000999] Calibrating delay using timer specific routine.. 3339.28 BogoMIPS (lpj=1669643) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 24K [ 0.000999] CPU: L2 cache: 512K [ 0.000999] CPU 3/0x3 -> Node 0 [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] mce: CPU supports 5 MCE banks [ 0.000999] CPU3: Thermal monitoring enabled (TM1) [ 0.000999] x86 PAT enabled: cpu 3, old 0x7040600070406, new 0x7010600070106 [ 0.259714] CPU3: Intel(R) Atom(TM) CPU D510 @ 1.66GHz stepping 0a [ 0.260125] checking TSC synchronization [CPU#0 -> CPU#3]: passed. [ 0.261002] Brought up 4 CPUs [ 0.261124] Total of 4 processors activated (13313.48 BogoMIPS). [ 0.262072] khelper used greatest stack depth: 5864 bytes left [ 0.263322] xor: automatically using best checksumming function: generic_sse [ 0.267966] generic_sse: 5056.000 MB/sec [ 0.268091] xor: using function: generic_sse (5056.000 MB/sec) [ 0.268242] Time: 23:40:25 Date: 02/21/19 [ 0.268477] NET: Registered protocol family 16 [ 0.269014] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.269966] ACPI: bus type pci registered [ 0.270117] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.270143] PCI: Not using MMCONFIG. [ 0.270264] PCI: Using configuration type 1 for base access [ 0.284028] bio: create slab <bio-0> at 0 [ 0.309781] ACPI: Interpreter enabled [ 0.309914] ACPI: (supports S0 S1 S3 S4 S5) [ 0.310261] ACPI: Using IOAPIC for interrupt routing [ 0.310508] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.323188] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources [ 0.342039] PCI: Using MMCONFIG at e0000000 - efffffff [ 0.369170] ACPI Warning: Incorrect checksum in table [OEMB] - 4D, should be 4A 20090521 tbutils-246 [ 0.370755] ACPI: No dock devices found. [ 0.372166] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.372417] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.372440] pci 0000:00:1c.0: PME# disabled [ 0.373086] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 0.373222] pci 0000:00:1c.4: PME# disabled [ 0.373412] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold [ 0.373544] pci 0000:00:1c.5: PME# disabled [ 0.374091] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.374224] pci 0000:00:1d.7: PME# disabled [ 0.374509] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.374723] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.374857] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) [ 0.375167] pci 0000:00:1f.2: PME# supported from D3hot [ 0.375296] pci 0000:00:1f.2: PME# disabled [ 0.375606] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold [ 0.375740] pci 0000:04:00.0: PME# disabled [ 0.376165] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.376300] pci 0000:03:00.0: PME# disabled [ 0.376648] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.376783] pci 0000:02:00.0: PME# disabled [ 0.377048] pci 0000:00:1e.0: transparent bridge [ 0.409159] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12 14 15) [ 0.409921] ACPI: PCI Interrupt Link [LNKB] (IRQs *7) [ 0.410394] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 12 *14 15) [ 0.411174] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12 14 15) [ 0.411925] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.412814] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.413719] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. [ 0.414644] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 6 7 10 11 12 14 *15) [ 0.416093] SCSI subsystem initialized [ 0.433668] raid6: int64x1 320 MB/s [ 0.450634] raid6: int64x2 500 MB/s [ 0.467696] raid6: int64x4 628 MB/s [ 0.484658] raid6: int64x8 667 MB/s [ 0.501688] raid6: sse2x1 324 MB/s [ 0.518675] raid6: sse2x2 218 MB/s [ 0.535715] raid6: sse2x4 433 MB/s [ 0.535837] raid6: using algorithm sse2x4 (433 MB/s) [ 0.536084] PCI: Using ACPI for IRQ routing [ 0.553105] cfg80211: Using static regulatory domain info [ 0.553191] cfg80211: Regulatory domain: US [ 0.553314] ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.554008] ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.554008] ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.554008] ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.554008] ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.554141] ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.554274] ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.554419] cfg80211: Calling CRDA for country: US [ 0.555041] NetLabel: Initializing [ 0.555138] NetLabel: domain hash size = 128 [ 0.555261] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.555261] NetLabel: unlabeled traffic allowed by default [ 0.555261] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 0.555368] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.556149] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 0.568391] pnp: PnP ACPI init [ 0.568557] ACPI: bus type pnp registered [ 0.580547] pnp: PnP ACPI: found 13 devices [ 0.580677] ACPI: ACPI bus type pnp unregistered [ 0.580825] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved [ 0.580959] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved [ 0.581111] system 00:08: ioport range 0xa00-0xa0f has been reserved [ 0.581242] system 00:08: ioport range 0xa10-0xa1f has been reserved [ 0.581382] system 00:08: ioport range 0xa20-0xa2f has been reserved [ 0.581515] system 00:08: ioport range 0xa30-0xa3f has been reserved [ 0.581674] system 00:09: ioport range 0x4d0-0x4d1 has been reserved [ 0.581807] system 00:09: ioport range 0x800-0x87f has been reserved [ 0.581941] system 00:09: ioport range 0x480-0x4ff could not be reserved [ 0.582079] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.582214] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.582350] system 00:09: iomem range 0xfed40000-0xfed8ffff has been reserved [ 0.582504] system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved [ 0.582715] system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.582858] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved [ 0.583007] system 00:0c: iomem range 0x0-0x9ffff could not be reserved [ 0.583140] system 00:0c: iomem range 0xc0000-0xcffff has been reserved [ 0.583273] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved [ 0.583418] system 00:0c: iomem range 0x100000-0xbf6fffff could not be reserved [ 0.583628] system 00:0c: iomem range 0xfed90000-0xffffffff could not be reserved [ 0.590122] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:04 [ 0.590256] pci 0000:00:1c.0: IO window: disabled [ 0.590393] pci 0000:00:1c.0: MEM window: 0xfeb00000-0xfebfffff [ 0.590525] pci 0000:00:1c.0: PREFETCH window: disabled [ 0.590655] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 [ 0.590786] pci 0000:00:1c.4: IO window: 0xe000-0xefff [ 0.590916] pci 0000:00:1c.4: MEM window: 0xfea00000-0xfeafffff [ 0.591048] pci 0000:00:1c.4: PREFETCH window: disabled [ 0.591177] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:02 [ 0.591307] pci 0000:00:1c.5: IO window: 0xd000-0xdfff [ 0.591445] pci 0000:00:1c.5: MEM window: 0xfe900000-0xfe9fffff [ 0.591577] pci 0000:00:1c.5: PREFETCH window: disabled [ 0.591707] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01 [ 0.591835] pci 0000:00:1e.0: IO window: disabled [ 0.591962] pci 0000:00:1e.0: MEM window: disabled [ 0.592092] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.592256] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.592415] pci 0000:00:1c.4: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.592577] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.592885] NET: Registered protocol family 2 [ 0.593482] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.597468] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.603703] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.604554] TCP: Hash tables configured (established 524288 bind 65536) [ 0.606905] TCP reno registered [ 0.607320] NET: Registered protocol family 1 [ 0.607640] Trying to unpack rootfs image as initramfs... [ 0.608272] rootfs image is not initramfs (no cpio magic); looks like an initrd [ 0.636184] Freeing initrd memory: 17634k freed [ 0.655634] microcode: CPU0 sig=0x106ca, pf=0x8, revision=0x107 [ 0.655797] microcode: CPU1 sig=0x106ca, pf=0x8, revision=0x107 [ 0.655944] microcode: CPU2 sig=0x106ca, pf=0x8, revision=0x107 [ 0.656091] microcode: CPU3 sig=0x106ca, pf=0x8, revision=0x107 [ 0.656373] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba [ 0.656587] Scanning for low memory corruption every 60 seconds [ 0.657496] audit: initializing netlink socket (disabled) [ 0.657673] type=2000 audit(1550792425.656:1): initialized [ 0.673649] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.682381] VFS: Disk quotas dquot_6.5.2 [ 0.682767] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.686619] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 0.687073] NTFS driver 2.1.29 [Flags: R/W]. [ 0.687785] fuse init (API version 7.12) [ 0.688382] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 0.690966] SGI XFS Quota Management subsystem [ 0.691127] msgmni has been set to 7909 [ 0.692985] alg: No test for stdrng (krng) [ 0.693132] async_tx: api initialized (sync-only) [ 0.693688] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.693908] io scheduler noop registered [ 0.694038] io scheduler anticipatory registered [ 0.694167] io scheduler deadline registered [ 0.694547] io scheduler cfq registered (default) [ 0.697230] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.697642] Initializing ths8200_init [ 0.697875] Initializing dove_adi9889_init [ 0.698784] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.699010] ACPI: Power Button [PWRF] [ 0.699429] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 0.699648] ACPI: Power Button [PWRB] [ 0.700830] processor LNXCPU:00: registered as cooling_device0 [ 0.701626] processor LNXCPU:01: registered as cooling_device1 [ 0.702377] processor LNXCPU:02: registered as cooling_device2 [ 0.703092] processor LNXCPU:03: registered as cooling_device3 [ 0.723326] Non-volatile memory driver v1.3 [ 0.723521] Linux agpgart interface v0.103 [ 0.723767] agpgart-intel 0000:00:00.0: Intel IGD Chipset [ 0.724251] agpgart-intel 0000:00:00.0: detected 8188K stolen memory [ 0.727935] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.728465] [drm] Initialized drm 1.1.0 20060810 [ 0.728715] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.757855] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining [ 0.758118] [drm] MTRR allocation failed. Graphics performance may suffer. [ 0.877922] [drm] Big FIFO is enabled [ 0.940307] [drm] Big FIFO is enabled [ 0.940317] [drm] DAC-6: set mode 1024x768 17 [ 0.940379] [drm] Big FIFO is enabled [ 0.940392] [drm] Big FIFO is enabled [ 0.980586] Console: switching to colour frame buffer device 128x48 [ 0.991142] [drm] fb0: inteldrmfb frame buffer device [ 0.991447] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 0.991616] work_for_cpu used greatest stack depth: 3648 bytes left [ 0.991785] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.236125] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.480125] serial8250: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A [ 1.481223] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 1.481738] 00:07: ttyS1 at I/O 0x2f8 (irq = 5) is a 16550A [ 1.488659] brd: module loaded [ 1.491919] loop: module loaded [ 1.492998] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.493212] ** BUFFALO Disable Command Queuing Function [ahci 0000:00:1f.2] ** [ 1.493453] ahci 0000:00:1f.2: controller can't do NCQ, turning off CAP_NCQ [ 1.493654] ahci: SSS flag set, parallel bus scan disabled [ 1.493819] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 1.493990] ahci 0000:00:1f.2: flags: 64bit sntf stag pm led clo pio slum part ems [ 1.505195] scsi0 : ahci [ 1.505783] scsi1 : ahci [ 1.508114] scsi2 : ahci [ 1.510440] scsi3 : ahci [ 1.512762] scsi4 : ahci [ 1.515095] scsi5 : ahci [ 1.517666] ata1: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ff900 irq 28 [ 1.519880] ata2: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ff980 irq 28 [ 1.522101] ata3: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ffa00 irq 28 [ 1.524340] ata4: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ffa80 irq 28 [ 1.526589] ata5: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ffb00 irq 28 [ 1.528852] ata6: SATA max UDMA/133 abar m2048@0xfe8ff800 port 0xfe8ffb80 irq 28 [ 1.532132] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI [ 1.534530] Copyright (c) 1999-2006 Intel Corporation. [ 1.537124] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 [ 1.539681] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 1.542572] sk98lin 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.545347] sk98lin: Network Device Driver v10.85.9.3 [ 1.545351] (C)Copyright 1999-2010 Marvell(R). [ 1.552820] eth0: Generic Marvell Yukon chipset Ethernet device [ 1.555999] sk98lin 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.560968] eth1: Generic Marvell Yukon chipset Ethernet device [ 1.564857] PNP: No PS/2 controller found. Probing ports directly. [ 1.568724] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.572110] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.575757] mice: PS/2 mouse device common for all mice [ 1.580561] rtc_cmos 00:03: RTC can wake from S4 [ 1.584245] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 1.587802] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 1.591631] md: raid0 personality registered for level 0 [ 1.595282] md: raid1 personality registered for level 1 [ 1.598859] md: raid6 personality registered for level 6 [ 1.602346] md: raid5 personality registered for level 5 [ 1.605746] md: raid4 personality registered for level 4 [ 1.609755] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 1.613934] cpuidle: using governor ladder [ 1.617315] cpuidle: using governor menu [ 1.620958] Kernel event proc (C) BUFFALO INC. V.1.00 installed. [ 1.624373] MICON ctrl (C) BUFFALO INC. V.1.00 installed. [ 1.627839] UPSDRV (C) BUFFALO INC. V.1.00 installed. [ 1.631303] OMRON contact type ups shutdown support enabled! [ 1.634831] [hdd control module init proc] [ 1.638343] buffalo/gpio directory create successful..... [ 1.641815] hotplug directory create successful..... [ 1.645248] HDD0_PRESENT_STATUS_FILE create successful..... [ 1.648678] HDD1_PRESENT_STATUS_FILE create successful..... [ 1.651996] HDD2_PRESENT_STATUS_FILE create successful..... [ 1.655231] HDD3_PRESENT_STATUS_FILE create successful..... [ 1.658388] HDD4_PRESENT_STATUS_FILE create successful..... [ 1.661519] HDD5_PRESENT_STATUS_FILE create successful..... [ 1.664653] HDD6_PRESENT_STATUS_FILE create successful..... [ 1.667784] HDD7_PRESENT_STATUS_FILE create successful..... [ 1.670914] power_control directory create successful..... [ 1.674109] HDD0_POWER_STATUS_FILE create successful..... [ 1.677290] HDD1_POWER_STATUS_FILE create successful..... [ 1.680447] HDD2_POWER_STATUS_FILE create successful..... [ 1.683592] HDD3_POWER_STATUS_FILE create successful..... [ 1.686730] HDD4_POWER_STATUS_FILE create successful..... [ 1.689862] HDD5_POWER_STATUS_FILE create successful..... [ 1.692991] HDD6_POWER_STATUS_FILE create successful..... [ 1.696017] HDD7_POWER_STATUS_FILE create successful..... [ 1.698951] hdd control module 0.2 initialized... [ 1.701899] buffalo/gpio/switch directory create successful..... [ 1.704875] buffalo/gpio/switch/func create successful..... [ 1.707778] buffalo/gpio/switch/display create successful..... [ 1.710647] enter fan module init [ 1.713756] enter cmos module init [ 1.716786] Netfilter messages via NETLINK v0.30. [ 1.720462] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.723240] TCP cubic registered [ 1.725930] NET: Registered protocol family 17 [ 1.729475] RPC: Registered udp transport module. [ 1.732203] RPC: Registered tcp transport module. [ 1.735463] registered taskstats version 1 [ 1.738351] Magic number: 7:128:707 [ 1.835030] ata1: SATA link down (SStatus 0 SControl 300) [ 2.153030] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.183667] ata2.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133 [ 2.186403] ata2.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 2.192198] ata2.00: configured for UDMA/133 [ 2.206238] scsi 1:0:0:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5 [ 2.209940] sd 1:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) [ 2.210192] sd 1:0:0:0: Attached scsi generic sg0 type 0 [ 2.216036] sd 1:0:0:0: [sda] Write Protect is off [ 2.219061] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.222586] sda: sda1 sda2 sda3 sda4 sda5 sda6 [ 2.278646] sd 1:0:0:0: [sda] Attached SCSI disk [ 2.527029] ata3: SATA link down (SStatus 0 SControl 300) [ 2.846026] ata4: SATA link down (SStatus 0 SControl 300) [ 3.164026] ata5: SATA link down (SStatus 0 SControl 300) [ 3.482026] ata6: SATA link down (SStatus 0 SControl 300) [ 3.495085] md: Waiting for all devices to be available before autodetect [ 3.497917] md: If you don't use raid, use raid=noautodetect [ 3.501327] md: Autodetecting RAID arrays. [ 3.504238] md: Scanned 0 and added 0 devices. [ 3.507189] md: autorun ... [ 3.510160] md: ... autorun DONE. [ 3.513250] RAMDISK: gzip image found at block 0 [ 4.809328] VFS: Mounted root (ext2 filesystem) on device 1:0. [ 4.907427] bootver=BOOTVER=Unkown [ 4.910811] buffalo_series_name=TeraStation [ 4.914193] buffalo_product_name=TS-QVHL(SAIMEI) [ 5.482804] kjournald starting. Commit interval 5 seconds [ 5.486512] EXT3-fs: mounted filesystem with writeback data mode. [ 5.542797] kjournald starting. Commit interval 5 seconds [ 5.546695] EXT3 FS on sda1, internal journal [ 5.550431] EXT3-fs: mounted filesystem with writeback data mode. [ 6.579244] usbcore: registered new interface driver usbfs [ 6.583491] usbcore: registered new interface driver hub [ 6.587550] usbcore: registered new device driver usb [ 6.597474] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.601400] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 6.605299] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1 [ 6.609307] xhci_hcd 0000:04:00.0: irq 16, io mem 0xfebfe000 [ 6.613083] usb usb1: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor [ 6.617017] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.620928] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.624903] usb usb1: Product: xHCI Host Controller [ 6.628925] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 xhci_hcd [ 6.633042] usb usb1: SerialNumber: 0000:04:00.0 [ 6.637370] usb usb1: configuration #1 chosen from 1 choice [ 6.641607] hub 1-0:1.0: USB hub found [ 6.645639] hub 1-0:1.0: 4 ports detected [ 6.658369] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.662643] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 6.666888] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 6.671069] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 6.679155] ehci_hcd 0000:00:1d.7: debug port 1 [ 6.683302] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe8ff400 [ 6.696023] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 6.700164] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 6.704265] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.708394] usb usb2: Product: EHCI Host Controller [ 6.712508] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd [ 6.716655] usb usb2: SerialNumber: 0000:00:1d.7 [ 6.721035] usb usb2: configuration #1 chosen from 1 choice [ 6.725350] hub 2-0:1.0: USB hub found [ 6.729453] hub 2-0:1.0: 6 ports detected [ 6.741255] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.752805] uhci_hcd: USB Universal Host Controller Interface driver [ 6.757314] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 6.761485] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 6.765612] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 [ 6.769776] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000bc00 [ 6.773919] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.778103] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.782272] usb usb3: Product: UHCI Host Controller [ 6.786390] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 6.790556] usb usb3: SerialNumber: 0000:00:1d.0 [ 6.794885] usb usb3: configuration #1 chosen from 1 choice [ 6.799167] hub 3-0:1.0: USB hub found [ 6.803213] hub 3-0:1.0: 2 ports detected [ 6.807654] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 6.811793] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 6.815817] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 [ 6.819893] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c000 [ 6.824032] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.828160] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.832268] usb usb4: Product: UHCI Host Controller [ 6.836348] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 6.840467] usb usb4: SerialNumber: 0000:00:1d.1 [ 6.844813] usb usb4: configuration #1 chosen from 1 choice [ 6.849021] hub 4-0:1.0: USB hub found [ 6.852946] hub 4-0:1.0: 2 ports detected [ 6.857225] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 6.861202] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 6.865121] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 [ 6.869112] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c080 [ 6.873107] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 6.877074] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.881088] usb usb5: Product: UHCI Host Controller [ 6.885046] usb usb5: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 6.889025] usb usb5: SerialNumber: 0000:00:1d.2 [ 6.893235] usb usb5: configuration #1 chosen from 1 choice [ 6.897352] hub 5-0:1.0: USB hub found [ 6.901297] hub 5-0:1.0: 2 ports detected [ 6.911507] usbcore: registered new interface driver libusual [ 6.926341] Initializing USB Mass Storage driver... [ 6.930505] usbcore: registered new interface driver usb-storage [ 6.934506] USB Mass Storage support registered. [ 6.945840] usbcore: registered new interface driver usblp [ 6.961975] usbcore: registered new interface driver hiddev [ 6.966042] usbcore: registered new interface driver usbhid [ 6.969935] usbhid: v2.6:USB HID core driver [ 7.097422] usb 2-2: new high speed USB device using ehci_hcd and address 3 [ 7.217205] usb 2-2: New USB device found, idVendor=0930, idProduct=6544 [ 7.221161] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.225122] usb 2-2: Product: TransMemory [ 7.229024] usb 2-2: Manufacturer: TOSHIBA [ 7.232884] usb 2-2: SerialNumber: BF988B2B1082CCA06C1E0C8B [ 7.237071] usb 2-2: configuration #1 chosen from 1 choice [ 7.241490] scsi6 : SCSI emulation for USB Mass Storage devices [ 7.451022] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 7.625880] usb 3-1: New USB device found, idVendor=0518, idProduct=0001 [ 7.629812] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 7.633705] usb 3-1: Product: USB-compliant keyboard [ 7.637573] usb 3-1: Manufacturer: Plus More Enterprise LTD. [ 7.641738] usb 3-1: configuration #1 chosen from 1 choice [ 7.663576] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.0/input/input2 [ 7.672122] generic-usb 0003:0518:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0 [ 7.697694] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.1/input/input3 [ 7.707317] generic-usb 0003:0518:0001.0002: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1 [ 12.262703] scsi 6:0:0:0: Direct-Access TOSHIBA TransMemory 1.00 PQ: 0 ANSI: 4 [ 12.273539] sd 6:0:0:0: Attached scsi generic sg1 type 0 [ 12.273924] sd 6:0:0:0: [sdb] 15155200 512-byte logical blocks: (7.75 GB/7.22 GiB) [ 12.284074] sd 6:0:0:0: [sdb] Write Protect is off [ 12.289146] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 12.296669] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 12.301671] sdb: sdb1 [ 12.309416] sd 6:0:0:0: [sdb] Assuming drive cache: write through [ 12.314411] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 33.808985] kjournald starting. Commit interval 5 seconds [ 33.809013] EXT3-fs: mounted filesystem with writeback data mode. [ 33.950273] md: md0 stopped. [ 33.956483] md: bind<sda1> [ 33.966269] raid1: raid set md0 active with 1 out of 4 mirrors [ 33.971034] md0: detected capacity change from 0 to 5120131072 [ 34.003389] md: md1 stopped. [ 34.009599] md: bind<sda2> [ 34.019357] raid1: raid set md1 active with 1 out of 4 mirrors [ 34.024327] md1: bitmap initialized from disk: read 1/1 pages, set 12 bits [ 34.029068] created bitmap (1 pages) for device md1 [ 34.045741] md1: detected capacity change from 0 to 16382877696 [ 34.077118] md: md2 stopped. [ 34.083057] md: bind<sda5> [ 34.092407] raid1: raid set md2 active with 1 out of 4 mirrors [ 34.096822] md2: bitmap initialized from disk: read 1/1 pages, set 0 bits [ 34.100910] created bitmap (1 pages) for device md2 [ 34.118219] md2: detected capacity change from 0 to 4095725568 [ 34.198249] md0: unknown partition table [ 34.471399] kjournald starting. Commit interval 5 seconds [ 34.479567] EXT3 FS on md0, internal journal [ 34.483288] EXT3-fs: mounted filesystem with writeback data mode. [ 34.507412] md1: unknown partition table [ 34.541536] kjournald starting. Commit interval 5 seconds [ 34.585839] EXT3 FS on md1, internal journal [ 34.589602] EXT3-fs: mounted filesystem with writeback data mode. [ 35.819723] kjournald starting. Commit interval 5 seconds [ 35.827440] EXT3 FS on md1, internal journal [ 35.831443] EXT3-fs: mounted filesystem with writeback data mode. [ 35.982045] usbcore: deregistering interface driver usbhid [ 36.034998] usbcore: deregistering interface driver hiddev [ 36.047142] usbcore: deregistering interface driver usblp [ 36.059029] usbcore: deregistering interface driver usb-storage [ 36.070029] usbcore: deregistering interface driver libusual [ 36.081174] uhci_hcd 0000:00:1d.2: remove, state 4 [ 36.085067] usb usb5: USB disconnect, address 1 [ 36.089656] uhci_hcd 0000:00:1d.2: USB bus 5 deregistered [ 36.093533] uhci_hcd 0000:00:1d.2: PCI INT C disabled [ 36.097322] uhci_hcd 0000:00:1d.1: remove, state 4 [ 36.101114] usb usb4: USB disconnect, address 1 [ 36.105576] uhci_hcd 0000:00:1d.1: USB bus 4 deregistered [ 36.109367] uhci_hcd 0000:00:1d.1: PCI INT B disabled [ 36.113075] uhci_hcd 0000:00:1d.0: remove, state 1 [ 36.116717] usb usb3: USB disconnect, address 1 [ 36.120305] usb 3-1: USB disconnect, address 2 [ 36.125413] uhci_hcd 0000:00:1d.0: USB bus 3 deregistered [ 36.129084] uhci_hcd 0000:00:1d.0: PCI INT A disabled [ 36.147050] ehci_hcd 0000:00:1d.7: remove, state 1 [ 36.150601] usb usb2: USB disconnect, address 1 [ 36.154072] usb 2-2: USB disconnect, address 3 [ 36.162656] ehci_hcd 0000:00:1d.7: USB bus 2 deregistered [ 36.166138] ehci_hcd 0000:00:1d.7: PCI INT A disabled [ 36.176184] xhci_hcd 0000:04:00.0: remove, state 1 [ 36.179569] usb usb1: USB disconnect, address 1 [ 36.184631] xhci_hcd 0000:04:00.0: Host controller not halted, aborting reset. [ 36.194004] xhci_hcd 0000:04:00.0: USB bus 1 deregistered [ 36.197557] xhci_hcd 0000:04:00.0: PCI INT A disabled [ 36.205155] usbcore: deregistering device driver usb [ 36.208711] usbcore: deregistering interface driver usbfs [ 36.212277] usbcore: deregistering interface driver hub [ 36.236342] VFS: Mounted root (ext3 filesystem) on device 9:1. [ 36.239579] Trying to move old root to /initrd ... okay [ 36.247772] Freeing unused kernel memory: 548k freed [ 36.251245] Write protecting the kernel read-only data: 7448k [ 38.491649] EXT3-fs: Unrecognized mount option "relatime" or missing value [ 39.222368] md2: unknown partition table [ 39.235178] Adding 3999724k swap on /dev/md2. Priority:-1 extents:1 across:3999724k [ 40.017721] kjournald starting. Commit interval 5 seconds [ 40.045020] EXT3 FS on md0, internal journal [ 40.048634] EXT3-fs: mounted filesystem with writeback data mode. [ 41.608569] ufsd: module license 'Commercial product' taints kernel. [ 41.612173] Disabling lock debugging due to kernel taint [ 41.779643] ufsd: driver 8.1 (Oct 13 2010 12:00:47) with acl LBD=OFF with ioctl loaded at ffffffffa0000000 [ 41.779651] NTFS read/write support included [ 41.944033] usbcore: registered new interface driver usbfs [ 41.952581] usbcore: registered new interface driver hub [ 41.953018] usbcore: registered new device driver usb [ 41.965338] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 41.965434] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 41.965526] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1 [ 41.965710] xhci_hcd 0000:04:00.0: irq 16, io mem 0xfebfe000 [ 41.965773] usb usb1: config 1 interface 0 altsetting 0 endpoint 0x81 has no SuperSpeed companion descriptor [ 41.965807] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 41.965815] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 41.965823] usb usb1: Product: xHCI Host Controller [ 41.965829] usb usb1: Manufacturer: Linux 2.6.31.8-atom_d510 xhci_hcd [ 41.965836] usb usb1: SerialNumber: 0000:04:00.0 [ 41.967954] usb usb1: configuration #1 chosen from 1 choice [ 41.968438] hub 1-0:1.0: USB hub found [ 41.968466] hub 1-0:1.0: 4 ports detected [ 41.983066] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 41.986143] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 42.021327] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 42.021382] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 42.025328] ehci_hcd 0000:00:1d.7: debug port 1 [ 42.025370] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfe8ff400 [ 42.035032] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 42.035098] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 42.035107] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 42.035115] usb usb2: Product: EHCI Host Controller [ 42.035121] usb usb2: Manufacturer: Linux 2.6.31.8-atom_d510 ehci_hcd [ 42.035128] usb usb2: SerialNumber: 0000:00:1d.7 [ 42.035622] usb usb2: configuration #1 chosen from 1 choice [ 42.036037] hub 2-0:1.0: USB hub found [ 42.036065] hub 2-0:1.0: 6 ports detected [ 42.045512] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 42.053739] uhci_hcd: USB Universal Host Controller Interface driver [ 42.055151] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 42.055184] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 42.055248] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 [ 42.055303] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000bc00 [ 42.055424] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 42.055432] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 42.055440] usb usb3: Product: UHCI Host Controller [ 42.055446] usb usb3: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 42.055453] usb usb3: SerialNumber: 0000:00:1d.0 [ 42.055952] usb usb3: configuration #1 chosen from 1 choice [ 42.056362] hub 3-0:1.0: USB hub found [ 42.056386] hub 3-0:1.0: 2 ports detected [ 42.057911] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 42.057939] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 42.057980] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 [ 42.058063] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c000 [ 42.058185] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 42.058194] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 42.058201] usb usb4: Product: UHCI Host Controller [ 42.058207] usb usb4: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 42.058215] usb usb4: SerialNumber: 0000:00:1d.1 [ 42.058726] usb usb4: configuration #1 chosen from 1 choice [ 42.059978] hub 4-0:1.0: USB hub found [ 42.060015] hub 4-0:1.0: 2 ports detected [ 42.061378] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 42.061408] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 42.061447] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 [ 42.061501] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c080 [ 42.061612] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 42.061620] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 42.061628] usb usb5: Product: UHCI Host Controller [ 42.061634] usb usb5: Manufacturer: Linux 2.6.31.8-atom_d510 uhci_hcd [ 42.061641] usb usb5: SerialNumber: 0000:00:1d.2 [ 42.062102] usb usb5: configuration #1 chosen from 1 choice [ 42.062514] hub 5-0:1.0: USB hub found [ 42.062543] hub 5-0:1.0: 2 ports detected [ 42.070580] usbcore: registered new interface driver libusual [ 42.082694] Initializing USB Mass Storage driver... [ 42.083077] usbcore: registered new interface driver usb-storage [ 42.083096] USB Mass Storage support registered. [ 42.091178] usbcore: registered new interface driver usblp [ 42.105376] usbcore: registered new interface driver hiddev [ 42.106911] usbcore: registered new interface driver usbhid [ 42.106927] usbhid: v2.6:USB HID core driver [ 42.259684] Warning: dev (tty1) tty->count(4) != #fd's(3) in tty_release_dev [ 42.411693] Warning: dev (tty1) tty->count(19) != #fd's(18) in tty_release_dev [ 42.515057] usb 2-2: new high speed USB device using ehci_hcd and address 3 [ 42.632664] usb 2-2: New USB device found, idVendor=0930, idProduct=6544 [ 42.632672] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 42.632678] usb 2-2: Product: TransMemory [ 42.632682] usb 2-2: Manufacturer: TOSHIBA [ 42.632687] usb 2-2: SerialNumber: BF988B2B1082CCA06C1E0C8B [ 42.633207] usb 2-2: configuration #1 chosen from 1 choice [ 42.646193] Error handler scsi_eh_7 sleeping [ 42.646293] scsi7 : SCSI emulation for USB Mass Storage devices [ 42.661982] Warning: dev (tty1) tty->count(3) != #fd's(2) in tty_release_dev [ 42.868034] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 43.041359] usb 3-1: New USB device found, idVendor=0518, idProduct=0001 [ 43.044481] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 43.047662] usb 3-1: Product: USB-compliant keyboard [ 43.050879] usb 3-1: Manufacturer: Plus More Enterprise LTD. [ 43.054631] usb 3-1: configuration #1 chosen from 1 choice [ 43.084259] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.0/input/input4 [ 43.092909] generic-usb 0003:0518:0001.0003: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input0 [ 43.131406] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:1d.0/usb3/3-1/3-1:1.1/input/input5 [ 43.141128] generic-usb 0003:0518:0001.0004: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:1d.0-1/input1 [ 47.677651] scsi 7:0:0:0: Direct-Access TOSHIBA TransMemory 1.00 PQ: 0 ANSI: 4 [ 47.687238] sg_alloc: dev=1 [ 47.687832] sd 7:0:0:0: Attached scsi generic sg1 type 0 [ 47.691788] sd 7:0:0:0: [sdb] 15155200 512-byte logical blocks: (7.75 GB/7.22 GiB) [ 47.692444] sd 7:0:0:0: [sdb] Write Protect is off [ 47.692462] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 47.719160] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 47.719176] sdb: sdb1 [ 47.739142] sd 7:0:0:0: [sdb] Assuming drive cache: write through [ 47.739153] sd 7:0:0:0: [sdb] Attached SCSI removable disk [ 54.152628] eth0: network connection up using port A [ 54.152628] interrupt src: MSI [ 54.152628] speed: 1000 [ 54.152628] autonegotiation: yes [ 54.152628] duplex mode: full [ 54.152628] flowctrl: symmetric [ 54.152628] role: slave [ 54.152628] tcp offload: enabled [ 54.152628] scatter-gather: enabled [ 54.152628] tx-checksum: enabled [ 54.152628] rx-checksum: enabled [ 54.152628] rx-polling: enabled [ 90.924364] md: md10 stopped. [ 91.006196] md: bind<sda6> [ 150.828085] set AC Power Loss to 0 [ 164.274957] set Wake on LAN to 1